background image

ENGLISH

62

Auto run, Fan operation

(1) Unit start

Press ON/OFF button, unit starts.
Previous operation status appears on display.
(Not Timer setting)
Power indicator on indoor unit lights up.

(2) Select operation mode

Press MODE button. For each press, operation mode changes as follows:

Unit will run in selected mode.
Stop display at "      ” AUTO or "      ” FAN.

(3) FAN 

Press FAN button. For each press, fan speed changes
as follows:
Unit will run at selected fan speed.

Note:AUTO is not available in FAN mode.

(4) Unit stop

Press ON/OFF button.
Only time remains on LCD.
All indicators on indoor unit go out.
Vertical flap closed automatically.

Hints
Remote controller can memorize settings in each operation mode. To run it
next time just
select the operation mode and it will start with the previous setting.
No reselecting is needed.(TIMER ON/OFF needs reselecting)

Cautions:

Note:

EOn cooling only unit, heating mode is not available, After replacing

batteries, press ON/OFF, and display
becomes as follows:
Operation mode: AUTO, Temp. No
Timer mode: No, Fan speed :AUTO

Note:

The above information is the explanation of the displayed informa-

tion therefore varies with those displayed in actual  operation.

OPERATION

Manual 1Hiyasu Eng  15/12/04  11:32  Página 62

Summary of Contents for ASE22U


















Reviews: