manualshive.com logo in svg

Hiyasu ASE22U, Manual, Page: 3 / 17

Share
Download
Hiyasu ASE22U Manual Download Page 3

ENGLISH

58

The machine is adaptive in following situation
1. Applicable ambient temperature range:

2. If the supply cord is damaged, it must be replaced by the manufacturer or its service agent
or a similar qualified person. The type of connecting wire is H05RN-F or H07RN-F.
3. If the fuse on PC board is broken please change it with the type of T.3.15A/250V.
4. The distance between the indoor unit and the floor should be more than 2m.
5. The wiring method should be in line with the local wiring standard.
6. After installation, the power plug should be easily reached.
7. The waste battery should be disposed properly.
8 .The wiring diagram is attached inside the machine. 

Outdoor Unit

CONNECTING PIPING AND
ELECTRICAL WIRING

INLET

OUTLET

DRAIN HOSE

PARTS AND FUNCTIONS

Indoor

Maximum: D.B/W.B

32ºC

Cooling

Minimum: D.B/W.B

18ºC/14ºC

Outdoor

Maximum: D.B/W.B

43ºC/26ºC

Minimum: D.B

18ºC

Indoor

Maximum: D.B

27ºC

Heating

Minimum: D.B

15ºC

Outdoor

Maximum: D.B/W.B

24ºC/18ºC

Minimum: D.B/W.B

-7ºC/-8ºC

Manual 1Hiyasu Eng  15/12/04  11:32  Página 58

Summary of Contents for ASE22U


















Reviews:

No comments