HITSA BORCH Technical Manual Download Page 6

HITSA BORCH Compressor Pump 

 

                       

SAFETY INFORMATION 

IMPORTANT: 

Read these instructions before product installation and operation

 

 

Before product installation and operation, please read the following safety 

information and sections in this manual concerning operation and installation. In 

addition to addressing safety concerns, reading this material will also help prevent 

damage to the product.  

 

Failure to install and operate this product in accordance with this information 

or using unauthorized spare parts could cause damage to the product and 

could result in severe bodily injury, including death in extreme cases. 

 

 
GENERAL SAFETY INFORMATION 

  If this product has been damaged, the power supply should be turned off 

immediately by a qualified service technician or electricity provider.  

  Only qualified service technicians should carry out service on this product.  

  Wear safety glasses, when servicing this product. 

  Compressed air can be dangerous; do not direct airflow at a person's head 

or body. 

 

 

TO REDUCE RISK OF ELECTRIC SHOCK 

  Do not use this product with electrical voltages other than those stated 

under Technical Specifications.  

  Do not install this product in any area where it will be subjected to above-

normal amounts of rainfall, other liquids, moisture, or areas subject to 

above-normal flood risk. 

  Do not attempt to service this product if it submerged in water. A qualified 

service technician or electricity provider should turn off the power supply to 

the product.  

 

TO REDUCE RISK OF EXPLOSION OR FIRE 

  Service and operate this product only in well ventilated areas. 

  During spraying with combustible liquids risk of explosion may arise, 

particularly in closed rooms. 

  Do not use this product in or near explosive atmospheres or where aerosol 

products are being used. 

  Do not use this product in or near areas with combustible or explosive 

liquids or vapors. 

  Do not use this product near naked flames. 

  Do not pump any other gases other than atmospheric air. 

  Do not pump combustible liquids or vapors with this product. 

 

 

Summary of Contents for BORCH






















Reviews: