background image

130-0047 Issue 8

G1010 OEM

Oxygen Analyser

Instruction Manual

This manual contains important Health & Safety information

SAFETY and EMC INFORMATION

Please read this section carefully before installing the instrument.

This instrument meets the requirements of the European directives specified below. However it is the responsibility of
the installer to ensure the safety and EMC compliance of any particular installation

Equipment:     

The G1010 range of gas analysers

.

Safety:     

These instruments comply with the European Low Voltage Directive 73/23/EEC, amended by 93/68/EEC by

the application of the safety standard EN61010(93)

Installation and servicing should only be carried out by suitably qualified personnel.

Electromagnetic Compatibility:     

These instruments comply with the EMC directive 89/336/EMC amended by

93/68/EEC, by the application of the following standards

:

EN50081 Part1:

1993 (Generic Emission Standard)

EN50082 Part1:

1995 (Generic Immunity Standard)

Installation Requirements for EMC:     

To ensure compliance with the European EMC directive certain installation

precautions are necessary as follows:

Instrument Rear Panel Rating

The G1010 instrument is designed as a panel mounted instrument and for this reason the back panel is rated as service
only. All service personnel should take electrostatic precautions before work is carried out at the rear of the instrument.

Radiated Emissions

In light industrial/domestic applications it may be necessary to suppress emissions from the power cable by fitting a
ferrite choke to the mains supply lead. The mains cable should be wound twice through the choke. (This choke is
available on request by quoting: Part No: 418-0045).

Routing of wires

To minimise the pick-up of electrical noise all signal wiring should be shielded and routed away from power cables.

Summary of Contents for G1010 Series













Reviews: