p22
p23
section 6
section 5
repeater preparation
Flying the quadcopter
Code Pairing:
1.Switch on the transmitter power switch, quadcopter power switch and repeater power switch respectively.
2. When Wi-Fi repeater’s blue light is on, the repeater is working normally. Toggle the S2 switch on the
transmitter to the center position from “OK,” and then toggle back to “OK.”
3. Press the repeater pairing button for 3sec. The Wi-Fi repeater blue light indicator blinks slowly [0.3sec ON,
3sec OFF.] This indicates the repeater has successfully paired with the onboard camera. If pairing fails, please
repeat steps above.
Charging the Repeater:
Connect the repeater to the Micro USB port through the repeater adapter to charge the repeater. It takes
about 2 hours to fully charge. Before each flight, make sure the repeater has a sufficient charge.
Switching on the Repeater:
1. Toggle repeater power switch to ON to switch on the repeater.
2. Wait until the Wi-Fi indicator blinks blue indicating that the repeater works properly.
3. While using this procecss, ensure the repeater’s LED side faces you and try to ensure that visibility between
the repeater and quadcopter is unobstructed to obtain maximum communication distance. After the flight is
completed, in addition to switching off the quadcopter and transmitter, be sure to turn off the repeater or else
the repeater’s battery will be depleted.
Check Battery Status:
In the Hitec AEE App camera interface, you can display and view the Q-Cop 450’s power information located in
the upper left corner of the screen.
Flying Environment Requirements:
1. Do not use the quadcopter in inclement weather, such as strong winds, snow, rain and fog.
2. Select an open area with no tall buildings as the flying site. Presence of a large number of steel buildings in
the area will affect the compass.
3. While flying the quadcopter, please stay away from obstacles, people, power lines, trees, shelters, water
bodies, etc.
4. Do not fly in a complex electromagnetic environment, such as near mobile phone base stations or towers, to
avoid transmitter interference.
5. This product cannot be used in the Antarctic and Arctic Circle.
6.Do not fly in restricted or no-fly zones and abide by relevant laws and regulations.
Pre-Flight Check:
1. Ensure transmitter, quadcopter, repeater and mobile device are fully charged.
2. Ensure rotor blades are correctly installed.
3. Ensure the Micro SD card is properly inserted before using the camera to capture images and videos.
4. Ensure S1 and S2 switches are in the “OK” position on the transmitter.
5. After powering on the quadcopter, transmitter and other equipment, please ensure they are working properly.
6. Check if the motors start properly after the quadcopter is switched on.
7. Check if the Hitec AEE App is properly connected to the camera.
Compass Calibration:
Compass calibration is required before first time use. Otherwise, the system may not work properly, affecting
flight safety. The compass is susceptible to interference from other electronic devices, resulting in data
anomalies, affecting the flight or even leading to accidents. Frequent calibration ensures the compass works
appropriately. Do not calibrate in a strong magnetic field. Do not carry ferromagnetic items such as keys, cell
phones, etc. while calibrating.
Calibration Procedures:
Please choose vast and open venues to conduct the calibration. Start the transmitter and quadcopter and
ensure the equipment works properly. Be sure to remove rotor blades before calibration to avoid accidental
injury. The Q-Cop needs a full battery before you begin. Follow the below procedures to calibrate the compass:
Step 1
Toggle Sticks to Above Position.
Front Indicator Blinks Green
Rotate Q-Cop 360 Degrees
Horizontally [Y Axis]
Rotate Quadcopter 360 Degrees
Vertically Facedown [Z Axis]
Rotate Q-Cop 360 Degrees [X Axis]
Front Indicator Turns OFF>ON Solid
Step 2
Step 3
Step 4
NULL
S1
S2
S3
S4
GPS
NRM
NULL
S1
S2
S3
S4
GPS
NRM
If done correctly the front indicator will turn Off then remain On solidly. If the indicator blinks rapidly instead,
please repeat steps 1-3 to obtain successful calibration.
Summary of Contents for AEE Q-COP 450
Page 1: ......
