![background image](http://html.mh-extra.com/html/hitachi/ultravision-ut47v702/ultravision-ut47v702_service-manual_141963019.webp)
D8MW
18
(4) Set the aspect to full mode.
(5) Set the color analizer (CA-210) at the center of the
panel.
Adjustment procedures
(1) Enter the Service mode.
(2) Check that the adjustment items no. 0, no. 1 and no. 2
of the Service Mode menu have the next initial values. If the
initial values are different, set them as the following data.
No. 0 = 230
No. 1 = 230
No. 2 = 240
(3) Receive the white raster signal. Step down two (or only
one) of either of the R DRV_COOL, G DRV_COOL or B
DRV_COOL adjustment parameters and change to the
following values
(NOTE: At least one of the adjustment parameters should
remain in the initial data value).
REMARKS
(1) Color temperature should be adjusted under the condition
in which the screen is the brightest, thus, the initial value of
the adjustment is set at its maximum.
This adjustment only decreases brightness.
(2) Beware, there is RESET in each picture mode.
(3) When the adjustment items no. 6, 7 or 8 are selected, the
color temperature of the picture changes to warm mode.
4.2 Normal Mode.
Adjustment preparations
(1) Adjustment signal: HDMI 1080i
Signal pattern: White raster
Video level: 90%
(2) Picture settings: Factory setting. Check that the mode is
set as the factory shipping conditions.
Picture mode: Dynamic.
(3) The color analyzer (CA-210) should be verified by a
spectrum radiation brightness meter such as the CS-1000
or standard LCD.
(4) Set aspect to full mode.
(5) Set the color analyzer (CA-210) at the center of the
panel.
Adjustment procedures.
(1) Enter the Service mode by following the procedure in
section 1.1.
(2) Check that the initial data of the adjustment items no. 3,
4 and 5 are in the following values. If their initial values are
different, change them as shown.
No. 3 = 224
No. 4 = 224
No. 5 = 224
(3) Receive the white raster signal. And decrease the value
of any two (or only one) of the R DRV_NORMAL, G DRV_
NORMAL or B DRV_NORMAL adjustment parameters in
order to get the X/Y coordinates to the following values.
REMARKS
(1) Color temperature should be adjusted under the condition
in which the screen is the brightest, thus, the initial value of
adjustment is set at its maximum.
(2) Beware there is RESET in each of the picture mode.
(3) When the adjustment items no. 6, 7 or 8 are selected, the
color temperature changes to warm mode.
Specification
Video Color Temperature (Cool)
x = 0.266 ± 0.005
y = 0.270 ± 0.005
14000K ± 0MPCD
Specification
Video Color Temperature (Normal)
x = 0.285 ± 0.005
y = 0.293 ± 0.005
9300K ± 0MPCD
Summary of Contents for UltraVision UT47V702
