1
Notes
1. Capacities included in these charts are the maximum allowable, and are based on machine standing level on firm supporting surface
under ideal job conditions.
2. Capacities are in metric tons, and are rated in accordance with European EN13000 Standards in terms of machine stability and
structural strength limitations.
3. Capacities are based on freely suspended loads and make no allowance for such factors as the effect of wind, sudden stopping
of loads, supporting surface conditions, and operating speeds. Operator must reduce load ratings to take such conditions into
account. Deduction from rated capacities must be made for weight of hook block, weighted ball/hook, sling, spreader bar, or other
suspended gear.
4. The maximum rated load of the auxiliary sheave is the value remaining after the mass of the “main hook” attached to the “Heavy Duty
Auxiliaury Tip Extension” are deducted from the maximum rated load of the “Heavy Duty Auxiliaury Tip Extension Capacities.”
However, the maximum rated load of the auxiliary sheave is limited to 15 tons. The operating range of the auxiliary sheave is the
range that has the maximum rated load of the main hook.
5. If the auxiliary hook is attached to the Auxiliary sheave, the maximum rated load of the “main hook” is the value remaining after the
mass of the auxiliary hook are deducted from the maximum rated load of the “Heavy Duty Auxiliaury Tip Extension Capacities.”
6. The "working radius" is the horizontal distance from the slewing center to the center of gravity of a lifted load.
7. The boom tilt angle range is according to the working range diagram.
8. The chart below shows the number of reeled lines and the maximum rated loads. (When the wire rope length is 800 m. )
9. The chart below shows the operable windings based on the length of each boom.
Hook Capacity (ton)
Hook Weight
(ton)
Maximum Rated Load ( ton )
7 Falls
6
Falls
5 Falls
4 Falls
3 Falls
2 Falls
1 Falls
160 Single-Reeling
3.9
100
90
76
-
-
-
-
65
Single-Reeling
*3.0 / 2.0
-
-
65
61
46
31
-
15
Single-Reeling
1.0
-
-
-
-
-
-
-
Hook Capacity (ton) / Boom Length (m)
66
72
78
84
90
96
160
Single-Reeling
Max.
7
7
7
7
7
6
Min.
5
5
5
5
5
5
65
Single-Reeling
Max.
5
5
5
5
5
5
Min.
2
2
2
2
2
2
15
Single-Reeling
-
-
-
-
-
-
6000SLX
Heavy Duty Tip Extension
* : With auxiliary weights / Without auxiliary weights
10. If the total mass of the hook mass and the mass of all rigging components is lighter than the mass indicated on this chart, the hook
may not lower even when a lowering operation is performed. Please select a hook that can be lowered based on the boom length
and number of windings.
Boom Length /
Number of reeled lines
1 Fall
2 Falls
3 Falls
4 Falls
5 Falls
6 Falls
7 Falls
66 m
1.0
2.0
2.0
2.0
2.0
3.9
3.9
72 m
1.0
2.0
2.0
2.0
2.1
3.9
3.9
78 m
1.0
2.0
2.0
2.0
2.3
3.9
3.9
84 m
1.0
2.0
2.0
2.0
2.4
3.9
3.9
90 m
1.0
2.0
2.0
2.1
2.6
3.9
3.9
96 m
1.0
2.0
2.0
2.2
2.8
3.9
-
11. The rated total load when the operation being performed with the rear post support pendant attached is the value remaining when
the value in chart below is deducted from the rated total load chart.
Boom Length (m)
66
72
78
84
90
96
Equivalent Mass (ton)
2.2
2.5
2.7
3.0
3.2
3.5
Summary of Contents for Sumitomo 6000SLX
