Hitachi SJ-EN Ethernet Communications, Instruction Manual

Page: 30 / 38

Appendix
Page 30 of 38
C034 2067 2068 Intelligent output 14 active state X1 R/W 0 – 1
C035 2069 2070 Intelligent output 15 active state X1 R/W 0 – 1
C036 2071 2072 Alarm relay output active state X1 R/W 0 – 1
C040 2079 2080 Overload signal output mode X1 R/W 0 – 1
C041 2081 2082 Overload level setting X10 R/W 0 – 2000
C042 2083 2084
Frequency arrival setting for
acceleration
X100 R/W 0 – 40000
C043 2085 2086
Arrival frequency setting for
deceleration
X100 R/W 0 – 40000
C044 2087 2088 PID deviation level setting X10 R/W 0 – 1000
C045 2089 2090
Frequency arrival setting for
acceleration (2)
X100 R/W 0 – 40000
C046 2091 2092
Arrival frequency setting for
deceleration (2)
X100 R/W 0 – 40000
C055 2109 2110 Over torque level – quadrant I X1 R/W 0 – 200 *
C056 2111 2112 Over torque level – quadrant II X1 R/W 0 – 200 *
C057 2113 2114 Over torque level – quadrant III X1 R/W 0 – 200 *
C058 2115 2116 Over torque level – quadrant IV X1 R/W 0 – 200 *
C061 2121 2122 Electronic thermal warning level X1 R/W 0 – 100
C062 2123 2124 Alarm code output X1 R/W 0 – 2
C063 2125 2126 Zero speed detection level X100 R/W 0 – 10000
C070 2139 2140 Data command method X1 R/W 2 – 5
C071 2141 2142 Communication speed selection X1 R/W 2 – 6
C072 2143 2144 Node allocation X1 R/W 1 – 32
C073 2145 2146 Communication data length X1 R/W 7 – 8
C074 2147 2148 Communication parity selection X1 R/W 0 – 2
C075 2149 2150 Communication stop bit selection X1 R/W 1 – 2
C078 2155 2156 Communication wait time X1 R/W 0 – 1000
C081 2161 2162 [O] input span calibration X1 R/W 0 – 65535
C082 2163 2164 [OI] input span calibration X1 R/W 0 – 65535
C083 2165 2166 [O2] input span calibration X1 R/W 0 – 65535
C085 2169 2170 Thermistor input tuning X10 R/W 0 – 10000
C086 2171 2172 [AM] output offset X10 R/W 0 – 100
C087 2173 2174 [AMI] output span X1 R/W 0 – 255
C088 2175 2176 [AMI] output offset X10 R/W 0 – 200
C091 2181 2182 Debug mode enable X1 R/W 0 – 1
C101 2201 2202 UP/DOWN memory mode X1 R/W 0 – 1
C102 2203 2204 RESET mode selection X1 R/W 0 – 2
C103 2205 2206 Restart mode after RESET X1 R/W 0 – 1
C111 2221 2222 Overload setting (2) X10 R/W 0 – 2000
C121 2241 2242 [O] input zero calibration X1 R/W 0 – 65535
C122 2243 2244 [OI] input zero calibration X1 R/W 0 – 65535