Hitachi RPIZ-0.8HNATNQ Operation Installation Maintenance Manual Download Page 5

Refrigerant R410A is non-flammable, non-toxic, and odorless, and may produce toxic gases when exposed to

 

open

flame.  Since  this  refrigerant  gas  is  heavier  than  air,  it  may  result  in  lack  of  oxygen,  thereby  leading  to

 

breathing

difficulties  when  the  area  near  the  ground  is  filled  with  this  gas.  If  that's  the  case,  please  turn  off  the

 

main  switch

immediately, cut off the power supply, and open the doors and windows for ventilation. Put out any

 

open flame, and

contact  your  service  dealer.  Performing  leak  detection  and  gas  tightness  test  with  oxygen,

 

acetylene  or  other

flammable and toxic gases may cause explosion, so nitrogen is recommended for this test.

The standards for safe refrigerant leakage in construction and system operation are determined based on local

regulations or standards.

Use ELB with medium or higher sensing speed (ELB with an operating time of 0.1 seconds or less), or

 

electric

shock or fire may arise.

For installation, the refrigerant piping must be firmly connected before the operation of compressor. For repair,

 

the

refrigerant piping must be moved, handled and removed after the stop of compressor.

Please don't short-circuit the protective device (e.g., the pressure switch, etc.) during operation, since this

 

may

cause fire or explosion.

Do not use any sprays such as insecticide, lacquer, hair spray or other flammable gases within approximately one (1) 

meter from the system.

If the earth leakage breaker (ELB) is frequently activated, please stop the system and contact your local dealer or 

customer services.

Make sure the ground wire is securely connected. The improper grounding of machine may lead to electrical failure. 

Please don't connect the ground wire to gas pipes, tap water pipes, lightning rods or phone ground wires.

Make sure there are no flammable materials around during brazing operation. Please wear leather gloves to prevent 

frostbite when filling refrigerant.

Prevent rats or other small animals damaging the wiring and electrical components. Bitten unprotected parts may 

cause a fire.

Firmly fix the connection wires. The external force of terminal may result in looseness of terminal that may cause a 

fire.

Make sure the air conditioner is installed with enough strength of fixation; otherwise, the air conditioner may fall or 

topple over, which may bring about machine damage or personal injury.

Please follow the installation instructions and related regulations and standards for electrical construction; otherwise, 

electrical failure or fire may occur due to inadequate capacity or inconsistent specifications. 

Never fail to use specified wiring and select correct wiring, since failure to do so may cause electrical failure or fire.

 

Please make sure the outdoor unit is not covered with snow  or ice before use.

This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or 

mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning 

use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. 

Cleaning and user maintenance shall not be made by children without supervision.

The A-weighted emission sound pressure don

'

t exceed 70 dB(A) .

This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or 

mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning 

use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance

Cleaning and user maintenance shall not be made by children without supervision.

本空调维修保养只能由专业人员进行。 

Please don't perform installation works such as refrigerant piping connection, drain pipe connection, and wiring 

connection. Violations may result in system leakage, electrical failure or fire. In the case of fire, please turn off the 

power immediately; please don't touch electrical parts with the hands, or electric shock may arise. 

Do not pour water into the indoor or outdoor unit. This machine is an electric product that may develop serious 

electric failure when exposed to water.

Do not open the service cover of indoor or outdoor units without turning OFF the main power supply; otherwise, this 

may bring about serious safety accident.

Do not touch or adjust safety devices inside the indoor or outdoor units. If they are touched or readjusted, serious 

accident may arise.

DANGER

WARNING 

 


Summary of Contents for RPIZ-0.8HNATNQ




















Reviews: