manualshive.com logo in svg

Hitachi RPFC-3.0UFE1NH, Installation & Maintenance Manual, Page: 20 / 28

Share
Download
Hitachi RPFC-3.0UFE1NH Installation & Maintenance Manual Download Page 20

3.2 

Installation location

• 

Select the suitable areas to install the unit with approval of 
the user.

• 

Ensure that the air path is not blocked.

• 

Ensure that condensate can drain properly.

• 

Ensure that the ceiling is strong enough to bear the weight of 
the indoor unit.

•  Ensure the sufficient clearance for maintenance and service. 

(See Fig.3.2.1).

• 

Piping between the indoor and outdoor units should be 
within the allowable limits. (Refer to the installation manual 
of the outdoor unit.)

• 

The indoor unit, outdoor unit, power supply wiring and 
transmission wiring should be at least 1 meter away from 
televisions and radio, to prevent interference and noise 
in those electrical appliances. (Noise may be generated 
depending on the conditions under which the electric wave is 
generated, even if one-meter.)

• 

Use suspension bolts to install the unit, check whether the 
ceiling is strong enough to support the weight of the unit. If 
there is a risk that the ceiling is not strong enough, reinforce 
the ceiling before installing the unit.

• 

If there are 2 units of wireless type, keep them at least 6m 
away to avoid malfunction due to cross communication.

• 

When plural indoor units are installed nearby, keep them 
away for more than 4-5m.

Space for installation and service

4000~5000mm or more

100mm or more

300mm  or more

150mm or more

5mm or more

Obstacle

Ceiling installation

4000~5000mm

100mm or more

150mm or more

150mm or more

Floor

150mm or more

Wall

Wall

Floor

Floor standing installation

Fig. 3.2.1 

3.3 

Installation

According to the actual installation space, installation can be 

done in the ceiling or on the floor.

3.3.1  Suspension bolts

1 

Consider the pipe direction, wiring and maintenance access 
carefully, and choose the proper direction and location for 
installation.

2 

Install the suspension bolts as shown in Fig. 3.3.1. below.

g

g

g

For concrete

For steel beam

For wooden beam

(W3/8 or M10)

Suspension 

bolts

Concrete

150 to 160mm

Screw in 

(100 to 150kg)

Steel 

bar

Wood rib 

(60mm to 90mm)

Wooden beam

“

I

” shaped steel 

beam

Suspension bolts 

(W3/8 or M10)

Nut

Round washer

Nut

Suspension bolts

Square washer

Fig. 3.3.1 Fixing the suspension bolts

3.3.2   Position of the suspension bolts and 

pipes

1 

Mark the positions of suspension bolts, refrigerant pipes and 
drain pipes.

2 

The dimensions are shown below.

17

0

68

0

39

39

A
B

25

0

(Unit: mm)

Blowout opening

Capacity

a

b

3.0HP

990

912

3.5/4.0HP

1285

1207

5.0/6.0/6.5HP

1580

1502

Fig. 3.3.2 Suspension bolts

INSTALLATION AND MAINTENANCE

HO2019291HA

14

Summary of Contents for RPFC-3.0UFE1NH





























Reviews:

No comments