Ð4
7Ð
¥ This controls the operation of the indoor unit.The range of control is about 7 meters. If indoor lighting is
controlled electronically, the range of control may be shorter.
This unit can be fixed on a wall using the fixture provided. Before fixing it, make sure the indoor unit can
be controlled from the remote controller.
¥ Handle the remote controller with care.Dropping it or getting it wet may compromise its signal transmission
capability.
¥ After new batteries are inserted into the remote controller, the unit will initially require approximately 10
seconds to respond to commands and operate.
¥ Do not put the remote controller in the following places.
¥ In direct sunlight
¥ In the vicinity of a heater.
¥ Handle the remote controller carefully. Do not drop it on the floor, and protect
it from water.
¥ Once the outdoor unit stops, it will not restart for about 3 minutes (unless you
turn the power switch off and on or unplug the power cord and plug it in
again).
This is to protect the device and does not indicate a failure.
¥ If you press the FUNCTION selector button during operation, the device may
stop for about 3 minutes for protection.
!
Point this window toward the indoor unit when controlling it.
The transmission sign blinks when a signal is sent.
"#
This indicates the room temperature selected, current time, timer status, function
and intensity of circulation selected.
! $
Press this button to start operation. Press it again to stop operation.
$
Use this button to set the sleep timer.
$
Use these buttons to raise or lower the temperature setting. (Keep pressed, and
the value will change more quickly.)
$
Use this button to set and checkthe time and date.
$
Use this button to select the operating mode. Every time you press it, the mode
will change from
(AUTO) to
(HEAT) to
(DEHUMIDIFY) to
(COOL)
and to
(FAN) cyclically.
This determines the fan speed. Every time you press this button, the intensity of
circulation will change from
(AUTO) to
(HI) to
(MED) to
(LOW).
(This button allows selecting the optimal or preferred fan speed for each operation
mode.)
% & $
Controls the angle of the horizontal air deflector.
Use these buttons to set the timer.
' $ Select the turn OFF time.
' $ Select the turn ON time.
( $ Time setting reservation.
$ Cancel time reservation.
AUTO
HEAT
DEHUMIDIFY
COOL
FAN
FAN SPEED
LOW
MED
HI
SLEEPING
STOP (CANCEL)
START (RESERVE)
START/STOP
TIME
TIMER SET
TIMER SELECTOR
ON TIMER
OFF TIMER
AUTO SWING
&
(
¥ If there is a power failure, operation will be automatically restarted when the power is resumed with
previous operation mode and airflow direction.
(As the operation is not stopped by remote controller.)
¥ If you intend not to continue the operation when the power is resumed, switch off the power supply.
When you switch on the circuit breaker, the operation will be automatically restarted with previous
operation mode and airflow direction.
Note: 1. If you do not require Auto Restart Control, please consult your sales agent.
2. Auto Restart Control is not available when Timer or Sleep Timer mode is set.
The device will automatically determine the mode of operation, HEAT, COOL, or DEHUMIDIFY, depending
on the initial room temperature. The selected mode of operation will change when the room temperature
varies.
Press the
(FAN SPEED) button, AUTO and LOW is available.
Press the
(START/STOP) button.
Operation starts with a beep.
Press the button again to stop operation.
As the settings are stored in memory in the remote controller, you only have
to press the
(START/STOP) button next time.
You can raise or lower the temperature setting as necessary by maximum
of 3¡C.
Press the temperature button and the temperature setting
will change by 1¡C each time.
¥ The preset temperature and the actual room temperature may vary
somewhat depending on conditions.
)
Press the FUNCTION selector so that the display indicates the
(AUTO) mode of operation.
¥ When AUTO has been selected, the device will automatically
determine the mode of operation, HEAT, COOL, or Dehumidify,
depending on the current room temperature.
