34
1
2
2
1
2
●
When you release your hand from a refrigerator door with the door open, the door may move, but this is normal.
Notice
BEFORE USE
1
2
3
Installing your refrigerator
●
The fl oor should be sturdy and fl at.
Lay a board with 1cm thickness on the fl oor if the refrigerator is installed on the carpet, tatami mat, fl ooring
or PVC sheet fl ooring which may be hollow or discolor.
●
Place the refrigerator away from direct sunlight and heat.
●
Do not place it in damp areas, and ensure good air ventilation.
This will reduce adverse effects to refrigerating power and keep electricity cost
down. This will also prevent the refrigerator from discoloring and rusting.
●
To cool effi ciently, allow enough space around the refrigerator for
radiating heat.
●
The actual size of the center part of the side of the refrigerator's main body
is slightly larger than the nominal size. Therefore, please allow enough space
around when installing the refrigerator.
●
The back of the refrigerator can be placed very close to the wall. If any
vibration sound occurs and/or any discolor/dirt is found on the wall,
move the refrigerator away from the wall.
Fix the refrigerator
Adjusting the refrigerator adjustable mount to keep it level
●
Left side or right side of the door may be slightly lower when the surface of the installation place is not level or either
of the left and right leg sinks in the fl oor surface because of the soft fl oor material and the addition of food weight.
→
This does not affect the refrigerator function. Adjust the refrigerator adjustable mount to keep it level according to the
procedure listed below if you want to correct it.
Correcting any left/right lean and lifting slightly the front side of the refrigerator until the door can close easily and completely.
To remove leg cover, hold both ends of it and
pull it towards to you by applying some force.
●
The adjustable mounts, which are located in the front bottom corners of the refrigerator, can be
adjusted by turning them to level the refrigerator. (Make sure to use a supplied tool and pads (2 pcs.))
Place pads under the adjustable mounts evenly.
※
Always wipe the adjustable mounts and fl oor
clean before placing pads. Adherents may
scratch the fl oor if they remain. Lower both
adjustable mounts (left and right) by turning
them to secure the refrigerator.
With the supplied tool, turn an adjustable mount on the side
so that the refrigerator is lower to make the Refrigerator
Compartment door level. (The height of the door can be
adjusted 1mm every one turn of the adjustable mount.)
Insert the left and right pins of
the leg cover into the mounting
holes to attach the leg cover.
It may be approx. 5 days before the
refrigerator conforms to the fl oor allowing
the door to be leveled. Readjustment is
required if the door is not leveled.
2
1
Leg cover
Cushion (Accessory)
Adjustable mounts
Preparation before use
Mounting hole
Fork
Leg cover
Required space above the
Required space above the
refrigerator: 5cm or more
refrigerator: 5cm or more
Required space for right and
Required space for right and
left of the refrigerator: 1 cm or more
left of the refrigerator: 1 cm or more
Clamp the supplied tool adjusting to the shape
of the adjustable mounts.
※
Only: “R-SF62CMJ”, “R-SF58CMJ”, “R-SF52CMJ”,
“R-S59CMJ”, “R-S53CMJ”
Supplied tool
1
1
■
The left door is
lower.
■
The left side of the
door is lower.
■
The right side of
the door is lower.
■
The right door
is lower.
Turn the left
Adjustable mount
to lower the left
side of the door.
Turn the right
Adjustable mount to
lower the right side
of the door.
