55
Case
現
象
Cause
原
因
•
The power supply switch does not work after the cutoff of the switch
and before the extinguishment of the mode LED. If the power supply is
switched on again, please press the switch after the LED extinguishes.
從切斷電源開關到程序指示燈熄滅為止，電源開關不起作用。
若要再次接通電源，請待指示燈熄滅後再按下電源開關。
The power supply switch may
not work right away when
switching from "Off" to "On".
電源開關由“斷開”轉換到“接
通”時，可能不會立即起作用。
•
The washing machine sound "Hoola, hoola" after the power supply is
switched on. About 1 second later, the LED light. (since the software
switch is used, the microcomputer need time for internal treatment.)
接通電源開關後，洗衣機發出“嗶嗶”的聲音，大約
1
秒鐘後指示燈點
亮。
（由於使用軟體開關，而微電腦進行內部處理需要時間）
The indicating LED won't light
right away when the power sup-
ply switch is switched on.
電源開關“接通”後，指示燈不會
立即點亮。
•
When switching off the power supply with clutch motor in spinning status,
the clutch motor returns to washing status and the mode LEDS light.
離合器電機在脫水狀態下，切斷電源開關時，離合器電機回復至洗滌
狀態，同時程序指示燈點亮。
Nine processes LEDS light after the
power supply switch is switched off.
電源開關“斷開”後，
9
個程序指示燈點亮。
• The operation stops after the power supply is switched off
during the spinning, and it buzzes. This is the sound generated
during switching of the modes by clutch.
脫水過程中切斷電源開關後，運轉停止並發出嗡嗡聲。這是離合器進
行模式切換時的聲音。
It buzzes after the power supply
switch is switched off.
電源開關“斷開”後，發出“嗡嗡”
的聲音。
• This is the odor of the insulating varnish of the motor at the be
-
ginning of use. The odor exists only at the early stage, and will
disappear after the machine is used for a period of time.
這是初期使用時從電機中的絕緣漆產生的氣味。該異味僅存在於初
期，使用一段時間後氣味會自動消失。
Odor of insulating varnish
smells in the beginning of use.
初期使用時有氣味。
• Adverse drainage condition or excessive foams (due to exces
-
sive detergent) may cause too much spinning load and make
the smell even more intensive.
排水條件惡劣或泡沫過多（因放入過多洗衣劑等）會造成脫水負荷過
大，使得氣味更加強烈。
It smells at the time of spinning.
脫水時有氣味。
• This is the water remains in the drainage hose during tests in
the factory.
這是工廠做性能測試時剩下的水。
Water comes out from the water
drainage hose during first time
usage.
第一次使用時，有水從排水管中流出。
• This is because the sensor can not successfully supply can be
cut off and the washing machine will be restarted.
這是由於外來干擾的影響而導致感測器無法正確檢測造成的。此時可
切斷電源，然後再次
啟動
。
Pulsator rotates but does not display the
washings load and water quantity after
pressing the Start button.
按下
啟動
按鈕後，攪拌翼轉動但沒
有顯示洗衣量和水位。
• This is because the washing machine is waiting for detergent or
is switching the clutch.
這是由於洗衣機在等待放入洗衣劑或正在進行切換離合器。
No reaction after starting.
啟動
後無動作。
There are detergent residue re-
mained on the detergent dispenser.
洗衣粉殘留在洗衣粉加入盤。
• When the machine body is excessive oblique, the detergent may
remain on the dispenser. Please check the obliquity of the body.
當機體過度傾斜時，洗衣粉可能會殘留在洗衣粉加入盤。請檢查機體
的傾斜程度。
•
Depending on the amount & types of laundries, air temperature &
moisture, seasons and environment, the completion time may differ.
由衣物的數量‧種類，氣溫‧濕度，季節和環境決定，完成時間會變化。
• Please refer to "Approximate air-jet duration".
40
請參照大致的風乾時間表。
40
It is not dried.
未乾。
About the air
jet processing
關於風乾
程度
• The preset time is the time for spinning, and the actual op
-
eration time includes the time of clothes rearrangement and
clothes balancing, which, will be longer than the preset time by
5~30 minutes.
設定時間是進行乾燥脫水的時間，實際運轉時間還要加上理順衣物和
糾正衣物偏斜的時間，大概比設定時間延長
5
至
30
分鐘。
Spinning does not complete
within the preset.
超過設定時間乾燥仍未結束。
About the
drying time
關於乾燥
時間
About the
power
switch
關於電源
開關
• After the power supply is cut off, the spinning basket stops
completely, and the lid lock will be unlocked.
當斷開電源，脫水槽完全停止後，機蓋鎖定將被解除。
The lid cannot be opened
even when the Pause button is
pressed during the spinning.
脫水過程中，即使按下暫停按鈕也
無法立即打開機蓋。
About the
lid lock
關於機蓋
鎖定
About the
flavor
關於氣味
Others
其他
