9
B
C
How to Use the Adjustable Leg
可調機腳的使用
1
Loosen the lock nut by unscrewing
in arrow direction
1
before using the
adjustable leg to stabilize unit.
將鎖緊螺母沿箭咀方向
1
旋鬆，再旋轉可
調機腳調整機身的平穩。
2
Lowering
⦲̥ᆹ
Loosening
ᅩ㌂
Lock nut
⽁ℤ➦ᕒ
Adjustable leg
ר⦲ᑨ⌳
Elevating
⦲㋧ᆹ
Maximum adjust able
range is 40mm.
⦲ῃߣ߱40mm˫ҙȯ
Tightening
ᅩℤ
Lock nut
⽁ℤ➦ᕒ
Plastic base
࢞ᅆಎᲷ
Tighten the lock nut until it reaches the plastic base.
⽁ℤ➦ᕒະე⎏࢞ᅆಎᲷᣅᔋȯ
At most 40mm
40mm
˫ʁ
Put some water into the washing barrel and reconfi rm its
horizontality.
在洗衣槽內放些水，請再一次確認其水平度。
•
The ground is level if all front, rear, left and right height difference between
the spinning hole and water surface are less than 3mm.
脫水孔相對於水面的高度差
(B
與
C
的差
)
，如果前後左右均在
3mm
以內，
就表示地面是水平的。
Installation of Washing Machine
洗衣機的安裝
1
Adjust the instability of the washing
machine with adjustable leg.
用可調機腳來調整洗衣機的不平穩。
2
Please make sure of the horizontality of
the washing machine.
請確認機體的水平度。
•
As shown in the fi gure, the horizontality can be easily
observed by the string used to hang an object.
如圖所示，用懸掛重物的細繩來觀察，即可輕易確認
其水平度。
Fixed leg
固定腳
Adjustable leg
可調機腳
Inspection of trial run
試運轉的檢查
■
To install the machine on an inclined fl oor, leg caps in the attached accessory kit can be used to adjust height by
connecting them to the fi xed leg.
安裝在傾斜的地面上時，請將附有的腳套套在固定腳上進行調整。
■
Confi rming the machine type of NW-80CSP/NW-70CSP, please install the water drninage hose and hang it on.
Otherwise there will be no water in washing basket.
10
NW-80CSP/NW-70CSP
機型確認時，請先安裝排水管並將其
連
起
/
排水管的安裝及固定方法。
10
否則洗衣槽內無法盛水。
A
A
It is level if the
clearance between
A and machine body
is the same with that
between
A
and the
machine body.
A
和
A
兩點與機體
之間的間隙相同，
即表示水平。
string
細繩
object
重物
(front or
profi le)
（正面或
側面）
After adjusting of the unit, tighten
the lock nut by screwing it in arrow
direction.
調整完畢後，將鎖緊螺母沿箭咀方向
2
旋緊。
