19
English
2. Trigger Lock Mechanism (See Fig. 7)
WARNING
Make sure the trigger is locked when not
fi
ring nails.
This Nailer has a lock mechanism to prevent the nails
from being
fi
red.
Set the switch lock lever at the position to lock the
trigger.
Slide the switch lock lever to the position when the
Nailer is to be used, and to the position when it is not
in use.
3. Testing the nailer
WARNING
○
Make sure the trigger is locked when not
fi
ring nails.
(See
Fig. 7
)
○
Never use Nailer unless push lever is operating properly.
The machine employs a preventive mechanism for
unloaded operation.
The machine enters a state where the push lever cannot
be pushed up. This takes place when the magazine is
not loaded with nails or when the remaining number of
nails becomes less than 9.
CAUTION
Use caution not to throw the push lever tip onto wood.
Before actually beginning the nailing work, test the Nailer by
using the checklist below. Conduct the tests in the following
order.
If abnormal operation occurs, stop using the Nailer and
contact a Hitachi authorized service center immediately.
(1) REMOVE ALL NAILS AND BATTERY FROM NAILER.
□
ALL SCREWS MUST BE TIGHTENED.
□
THE PUSH LEVER AND TRIGGER MUST MOVE
SMOOTHLY with pulling back the feeder knob.
(2) Installing the battery.
Do not operate the push lever or trigger while installing
the battery. (See
Fig. 2
)
(3) Turn on the Power switch. (See
Fig. 1
)
Turn on the Power switch by push and hold on Power
switch more than 1 second.
Make sure the power indicator is lighting in green, and
nailing operation indicator is lighting in blue. (FULL
SEQUENTIAL ACTUATION MECHANISM)
NOTE
Do not press the push lever and/or pull the trigger during
the process of turning the power switch ON.
Doing so will prevent the power switch from turning ON.
[Auto power o
ff
]
When the power is turned on but the Nailer is not used
for 30 minutes, the Nailer is automatically turned o
ff
. To
turn on again, press the power switch.
WARNING
Never leave the Nailer with the power on. This could
result in an accident.
Nailing operation indicator
Lighting
(Blue):
FULL SEQUENTIAL ACTUATION MECHANISM,
Blinking
(Blue):
CONTACT ACTUATION MECHANISM
(New Zealand product speci
fi
cations excluded)
Make sure the battery indicator is not blinking.
If the battery indicator is blinking in red, the battery
doesn’t have enough power and it needs to be charged.
(4) Remove the
fi
nger from the trigger and press the push
lever against the workpiece with pulling back the nail
feeder knob.
□
THE NAILER MUST NOT OPERATE.
(5) Separate the push lever from the workpiece.
Next, point the nailer downward, with pulling back the
feeder knob, pull the trigger and then wait in that position
for 5 seconds or longer.
□
THE NAILER MUST NOT OPERATE.
(6)
1
Without touching the trigger, depress the push lever
against the workpiece with pulling back the feeder
knob.
Next, pull the trigger.
□
THE NAILER MUST OPERATE.
2
Hold the trigger back and depress the push lever
against the workpiece again.
□
THE NAILER MUST NOT OPERATE.
3
Separate the
fi
nger from the trigger.
Next,
1
is operated again.
□
THE NAILER MUST OPERATE.
(7) Separate the push lever from the workpiece, pull the
trigger.
Depress the push lever against the workpiece within
2 seconds.
□
THE NAILER MUST NOT OPERATE.
(8) (New Zealand product speci
fi
cations excluded)
Set the nailing operation indicator blinking ON mode.
(CONTACT ACTUATION MECHANISM)
Push the nailing operation switch once, make sure that
the indicator is blinking Blue.
Separate the push lever from the workpiece, pull the
trigger.
Depress the push lever against the workpiece within
2 seconds.
□
THE NAILER MUST OPERATE.
(9) If no abnormal operation is observed, you may load nails
in the Nailer.
Drive nails into the workpiece that is the same type to be
used in the actual application.
□
THE NAILER MUST OPERATE PROPERLY.
4. Checking push lever operations
WARNING
Make sure the trigger is locked when not
fi
ring nails.
Always make sure the trigger is locked and the battery
removed from the power tool when checking push lever
operations.
Check to make sure the push lever slides smoothly when
operated.
Clean the sliding area on the push lever if it doesn’t slide
smoothly.
5. Load nails
WARNING
When loading nails into Nailer,
1) remove battery from the nailer;
2) do not pull trigger;
3) do not depress push lever; and
4) keep nailer pointed downward.
2–Action Nail Feeding!
(1) Insert nail strip into the back of the magazine. (See
Fig. 8
)
(2) Slide the nail strip forward in the magazine. (See
Fig. 9
)
(3) Pull the nail feeder (B) back to engage the feeder knob to
the nail strip. (See
Fig. 10
)
0000Book̲NR1890DBCL.indb 19
0000Book̲NR1890DBCL.indb 19
2017/08/17 15:54:57
2017/08/17 15:54:57
