Hitachi L3200 Manual Download Page 21

Page: 21 / 21

Page 21

...........................................................................

Technical details and Declaration of conformity

Full DECT GAP Compatible system

Standard

Frequency range

Channel bandwidth

Modulation

Operating range

Operating time

Temperature range

Electrical power

PABX compatibility

Languages:

Digital Enhanced Cordless

Telecommunications (DECT)

1.88 to 1.9 GHZ

1.728 MHZ

GMSK

Up to 300m outdoors; Up to 50m indoors

Standby time:5 days

Talking time: 10 hours

Operating 0 to 40

Storage -20 to 60

Handset---one 2.4 V 750 mAH Ni-MH,

rechargeable battery pack

Base unit---input 230 V AC, 50 Hz;

output AC 9 V, 300 mA.

Timed break recall: 100 ms for short flash;

250 ms for long flash

Pause length: 3 seconds.

Signaling type: DTMF(dual-tone multifrequency)

Pulse dialing

The L3200 complies with the essential protective

requirements and objectives of:

EC R& TTE Directive 1999/5/EC

EC Low Voltage Directive 73/23/EEC

EC EMC Directive 89/336/EEC

And conforms to the following relevant harmonized

standards:

Radio: TBR 6

EMC: EN 301489

Safety: EN 60950, EN 41003

Other: I-CTR 37, TBR 22

Declaration of conformity

Summary of Contents for L3200






















Search results

Summary of Contents for L3200

Reviews:

Related manuals for L3200

Brands by name

Popular brands

Hitachi L3200, Manual

Search results

Summary of Contents for L3200

Reviews:

Related manuals for L3200

Brands by name

Popular brands