Hitachi DVPF2E, Instruction Manual

Page: 20 / 57

– 20 – EN
2C15
• During reception of bilingual broadcasts:
Display on
the TV screen
Mode
MAIN
SUB
MAIN
SUB
MAIN
SUB
MAIN
SUB
Main Audio
Main Audio
Sub Audio
Sub Audio
Main Audio
Sub Audio
L
R
L
R
L
R
AUDIO OUTPUT
• Reception of stereo broadcasts:
STEREO
LEFT
RIGHT
- None -
Display on
the TV screen
Mode
Stereo
L
R
Monaural
L Audio
R Audio
L Audio
L Audio
R Audio
R Audio
L+R Audio
L+R Audio
L
R
L
R
L
R
L
R
AUDIO OUTPUT
• During playback of the recorded tape in
Hi-Fi mode:
Mode
Stereo
L
R
Normal
STEREO
LEFT
RIGHT
- None -
Display on
the TV screen
Hi Fi L Audio
Hi Fi R Audio
Hi Fi L Audio
Hi Fi L Audio
Hi Fi R Audio
Hi Fi R Audio
Normal Audio
Normal Audio
L
R
L
R
L
R
L
R
AUDIO OUTPUT
Notes
¡ If you play non-Hi-Fi tapes, the DVD/VCR will play automatically in monaural even if you select any mode.
¡
If the stereo signal becomes weak, the broadcast is automatically recorded in monaural.
This DVD/VCR will record and playback Hi-Fi stereo sound. In addition it has a NICAM stereo sound decoder.
This equipment will receive stereo and bilingual broadcasts and there are several ways of recording and play-
ing back the sound.
You can select each mode by pressing the AUDIO Button on the remote control. Each mode is indicated on the
TV screen as following.
VCR
Skip This Section When Connected By SCART.
Video channel setting will be necessary, if your
DVD/VCR is connected to the TV via the coaxial
cable.
• Use the remote control for this procedure.
1
Insert a pre-recorded tape into the
DVD/VCR.
• The DVD/VCR will turn on and start playback
automatically.
If playback does not start, press the
B
Button.
2
Select and adjust your TV to channel 35.
• If the playback picture appears on the TV screen,
continue with step 8.
• If channel 35 is employed for broadcasting, or
interference lines appear on the picture, the RF
converter must be set to a different channel
between CH22 and CH69. Continue with step 3.
3
Press the MENU Button.
4
Press the
B
or
C
Button repeatedly to
select “INITIAL”. Then,
press the
g
Button.
VCR
5
Press the
B
or
C
Button repeatedly to
select to “RF OUT”. Then, press the
g
Button.
• The RF OUT CH menu will appear.
6
Press the
B
or
C
Button to select a channel
which is not used for broadcasts between
channel 22 and channel 69 in your area, then
press the
g
Button.
7
Press the MENU button to exit.
• Set the TV channel to the RF OUT CHANNEL
which was selected on the DVD/VCR. Press
B
. A
picture from the DVD/VCR will appear on the TV
screen. If a picture does not appear, repeat steps 3
to 7 using a different channel which is not used for
broadcasts.
8
Press
C
to stop the tape.
Notes
• You may also access the RF OUT CH menu by
pressing and holding MENU on the remote control
for 3 seconds during power off until the RF OUT
CH menu appears.
• If your DVD/VCR and TV are connected using a
SCART cable there is no need to have the RF con-
verter operating so it can be switched off and avoid
the possibility of interference.
MENU
TIMER
SET UP
INITIAL
RF OUT CH 35
INITIAL
CH TUNING
CLOCK
RF OUT
HI-FI STEREO SOUND SYSTEM
PRESET FOR USE
SELECTING THE SOUND MODE
VIDEO CHANNEL SETTING