Tuning of broadcast channels not already preset in the
DVD/VCR can be performed in two ways.
AUTOMATIC TUNING
• By “AUTOMATICALLY” tuning channels and placing
them in sequential order in the DVD/VCR’s memory i.e.
the first channel found will be memorised into the
DVD/VCR’s channel position 1, the second channel
found will be memorised into the DVD/VCR’s channel
position 2 and so on.
• Execution of the “Automatic” tuning cancels all the pre-
set channels. DO NOT use this feature if you intend to
use some of the pre-tuned channels. Use the “Manual”
tuning function to tune in the additional channels you
require.
MANUAL TUNING
• Each channel is tuned manually and individually. Follow
the steps laid out in the “Manual tuning” section.
Before you preset Channel ...
• It is necessary to set the video channel if your
DVD/VCR is connected to the TV via the aerial cable,
and TV channel 36 is employed for broadcasting, or
interference lines appear on the picture. Please refer to
“Video Channel Setting”.
– 16 –
EN
This DVD/VCR incorporates a 24-hour clock. The clock must
be set for the Automatic Timer Recording function to operate
correctly.
Your DVD/VCR is fitted with VPS/PDC (Refer to page 21). If
the VPS/PDC signal is available in your area, your DVD/VCR
can get the current time from your local PDC broadcast. It
keeps track of the time constantly referring to the time broad-
casted by your VPS/PDC broadcast. If you want to use this
feature, refer to “Auto Clock Setting” in the next section.
• Use the remote control for this procedure.
Manual Clock Setting
Press
MENU
.
Press
K
or
L
to select “INITIAL”,
then press
B
B
.
Press
K
or
L
to select “CLOCK”,
then press
B
B
.
Press
K
or
L
to select “MANUAL”,
then press
B
B
.
Press
K
or
L
until the relevant year
appears, then press
B
B
.
Likewise, set the relevant month,
day, hour, and minute.
Press
MENU
to start the clock.
7
6
5
4
3
2
1
VCR
Setting the Clock
PRESET FOR USE
MENU
TIMER
SET UP
INITIAL
INITIAL
CH TUNING
CLOCK
RF OUT
LANGUAGE
GUIDE CHANNEL
CLOCK
YEAR
2 0 0 4
MONTH
0 1
DAY
0 7 WE
HOUR
_ _
MINUTE
_ _
NOTES:
• In the steps
and
, you can go back to the item
you want to correct by pressing
s
.
• Although seconds are not displayed, they begin count-
ing from 00 when you exit by pressing
MENU
. Use this
feature to synchronise the clock with the correct time.
• When unplugging the power-cord or if there is a power
failure for more than thirty seconds, you may have to
reset the clock.
Auto Clock Setting
Follow the steps through
to
in “Manual clock set-
ting”.
Press
K
or
L
to select “AUTO”, then press
B
B
to select
“ON”.
Turn off the DVD/VCR once by pressing
y
y
/I
(Power/Standby)
.
• The clock will appear on the TV screen when you turn
on the DVD/VCR again.
NOTES:
• Channel Presetting must be set before the Auto Clock
is set.
• The DVD/VCR refers to the channel which was memo-
rised into position 01.
The PDC channel must therefore be set to position 01.
• The clock cannot be set automatically if you are not
receiving a channel that carries a time signal in your
area. In this case, set the clock manually.
• Once the auto clock setting is performed, the DVD/VCR
will correct the current time by receiving PDC broad-
casts whenever you turn off the DVD/VCR.
• The DVD/VCR will correct the current time automatically
at 8:00, if the DVD/VCR’s power is turned off.
• Between 23:00~1:00, the AUTO CLOCK function does
not work even if the DVD/VCR’s power is turned off.
3
2
3
1
1
6
5
TUNING
Automatic Tuning
Turn on the TV and select the TV channel to the video
channel on the TV.
Press
MENU
.
Press
K
or
L
to select “INITIAL”,
then press
B
B
.
Press
K
or
L
to select “CH TUN-
ING”, then press
B
B
.
Press
K
or
L
to select “AUTO”,
then press
B
B
.
• The tuner scans and memorises
all the active channels in your
area. After scanning, the tuner
stops on the lowest memorised
channel.
To Select a Desired Channel
You can select a desired channel by using
the
PROG
(
K
or
L
), or directly pressing the
number but-
tons
on the remote control.
• Enter a channel numbers as a two-digit number for the
quickest results. For example, to select channel 6,
press
0
and
6
. If you only press
6
, channel 6 will be
selected after a brief delay.
• You can only select channels 1–99.
5
4
3
2
1
MENU
TIMER
SET UP
INITIAL
You can programme the tuner to scan only the channels that
you can receive in your area.
• Use the remote control for this procedure.
VCR
INITIAL
CH TUNING
CLOCK
RF OUT
LANGUAGE
GUIDE CHANNEL
CH TUNING
AUTO
MANUAL
MOVE
H9754ED(EN).qx4 04.5.31 3:24 PM Page 16
