Hitachi DS 12DVF2 Technical Data And Service Manual Download Page 27

Page: 27 / 41

--- 24 ---

(6) Other precautions in reassembly

(a) When the assembly procedure is completed, make sure that the turning direction of the Drill Chuck

10TLRD-N (W/O Chuck Wrench)

[2]

corresponds to the position of the Pushing Button

[36]

. When the

Pushing Button

[36]

is pressed from the (R)-marked side, the Drill Chuck 10TLRD-N (W/O Chuck Wrench)

[2]

should turn clockwise when viewed from the rear (opposite side of the Drill Chuck 10TLRD-N (W/O

Chuck Wrench)

[2]

). Also make sure that the turning speed of the Drill Chuck 10TLRD-N (W/O Chuck

Wrench)

[2]

switches between "HIGH" and "LOW" by switching over the Shift Knob

[38]

. Make sure that

the run-out of the Drill Chuck 10TLRD-N (W/O Chuck Wrench)

[2]

holding a 9 mm dia. test bar is below

0.8 mm at a distance of 85 mm from the chuck end.

(b) The tightening torque of each screw is given below.

Special Screw (Left Hand) M5 x 27

[1]

: 2.9 --- 3.9 N

•

m ( 30 --- 40 kgf

•

cm, 26.1 --- 34.8 in-lbs.)

Drill Chuck 10TLRD-N (W/O Chuck Wrench)

[2]

: 12.7 --- 16.7 N

•

m (130 --- 170 kgf

•

cm, 113 --- 148 in-lbs.)

Screw Set D3 x 12

[16]

: 0.6 --- 1.0 N

•

m ( 6 --- 10 kgf

•

cm, 5.2 --- 8.7 in-lbs.)

Machine Screw M3 x 8

[30]

: 0.6 --- 0.9 N

•

m ( 6.5 --- 9.5 kgf

•

cm, 5.6 --- 8.3 in-lbs.)

Tapping Screw (W/Flange) D3 x 16

[27]

: 1.1 --- 1.9 N

•

m ( 11 --- 19 kgf

•

cm, 9.5 --- 16.5 in-lbs.)

10-2. Precautions in Disassembly and Reassembly of Battery Charger

Please refer to the Technical Data and Service Manual for precautions in disassembly and reassembly of the

Battery Chargers UC 14SD, UC 12SD and UC 9SD.

Summary of Contents for DS 12DVF2










































Search results

Summary of Contents for DS 12DVF2

Reviews:

Related manuals for DS 12DVF2

Brands by name

Popular brands

Hitachi DS 12DVF2, Technical Data And Service Manual

Search results

Summary of Contents for DS 12DVF2

Reviews:

Related manuals for DS 12DVF2

Brands by name

Popular brands