Hitachi DKC910I Installation Manual Download Page 37

Page: 37 / 138

DKC910I

Hitachi Proprietary

[INST(RM)04-03-50]

Rev.2

INST(RM)04-03-50

Removing the Front Bezel
Remove the Front Bezel. (Refer to

“

How to Attach/Remove the Front Bezel

”

(INST(GE)04-05-10)

Checking the Drive Box LEDs
Check that the ALM LEDs (red) on the DBPSs installed in the Drive Box to be removed light up.

When the ALM LEDs do not light up, check that the PATH (IN) LEDs (green) / the Link LEDs (blue) on
the ENCs installed in the Drive Box to be removed are oﬀ.

Figure 4-2 ALM LED on DBPS

Rear view of SBX

ENCxxx-1

ENCxxx-2

ALM LED

PATH(IN) LED

DBPSxxx-1

DBPSxxx-2

Rear view of UBX

ENCxxx-1

ENCxxx-2

ALM LED

PATH(IN) LED

DBPSxxx-1

DBPSxxx-2

Rear view of FBX

ENCxxx-1

ENCxxx-2

ALM LED

PATH(IN) LED

DBPSxxx-1

DBPSxxx-2

Rear view of NBX

ENCxxx-1

ENCxxx-2

ALM LED

Link LED

DBPSxxx-1

DBPSxxx-2

Summary of Contents for DKC910I










































































































































Search results

Summary of Contents for DKC910I

Reviews:

Brands by name

Popular brands

Hitachi DKC910I, Installation Manual

Search results

Summary of Contents for DKC910I

Reviews:

Brands by name

Popular brands