background image

--- 24 ---

Front Cap 

[1]

Stopper Ring 

[2]

Ball Holder

 [4]

Holder Plate 

[5]

Holder Spring 

[6]

Washer (B) 

[7]

Grip 

[3]

Fig. 17

Steel Ball D7.0 

[17]

Grip 

[3]

Fig. 16

(4) Disassembly of the tool retainer

Slide the Grip 

[3]

 fully in the arrow direction as shown in Fig. 16 and remove the Front Cap 

[1]

.  Pulling the

Grip 

[3]

 as shown in Fig. 17, remove the Stopper Ring 

[2]

 with a retaining ring puller.  Then the Grip 

[3]

, Ball

Holder 

[4]

, Steel Ball D7.0 

[17]

, Holder Plate 

[5]

, Holder Spring

 [6]

 and Washer (B) 

[7]

 can be removed from

the Cylinder 

[18]

.

(5) Disassembly of the cylinder and the second gear (slip mechanism section)

Remove the Gear Cover 

[10]

 from the Inner Cover Ass'y 

[40]

 and remove the entire tool retainer.  Remove the

Retaining Ring for D20 Shaft 

[8]

 with a retaining ring puller.  Stand the Gear Cover 

[10]

 in this state and pull

out the Cylinder 

[18]

 from the Gear Cover 

[10]

 with a hand press.  Then Sleeve (A) 

[15]

 can be removed from

the Cylinder 

[18]

.  Remove the Retaining Ring 37 mm 

[27]

 from the Cylinder 

[18]

 with a retaining ring puller.

Then the Second Gear 

[19]

, Spring (A) 

[20]

 and Washer (A) 

[26]

 can be removed from the Cylinder 

[18]

.

Fig. 15

Change Lever 

[25]

Pushing Button [

22]

Summary of Contents for DH 24PD3













































Reviews: