Hitachi DH 24PD3 Technical Data And Service Manual Download Page 11

Page: 11 / 44

--- 8 ---

G. Driling hole (rotation only)

• • •

For drilling holes in steel and wood

Chuck adapter (D) (for SDS-plus shank type)

13 mm (1/2") Drill chuck 13VLD-D (with chuck wrench)

Part name

Code No.

303624

321813

3 --- 5 mm

6 --- 8 mm

Bit No.

No. 2

No. 3

H. Driving screws (rotation only)

Code No.

971511Z

971512Z

Drill chuck (13VLD-D)

(NOTE)
The 13VLA drill chuck and chuck adapter (D) cannot be used for reverse rotaion. If reverse rotation is to
be used for loosening screws, use the plus bit (Bit No. 2), described below, by attaching it directly to
chuck adapter (D).

Screw size

Chuck adapter (D)

(SDS-plus shank)

Chuck wrench

Bit No.

Chuck adapter (D)

(SDS-plus shank)

Code No. 971787

Code No. 306885

I. Grease for electric impact drill

Containing 500 g (1.1 lbs.): Code No. 980927

Containing 30 g (0.07 lbs.): Code No. 981840

70 g (0.15 lbs.): Code No. 308471

J. Dust cup, dust collector (B)

Dust cup

Dust collector (B) ass'y

Plus driver bit [overall length: 25 mm] (for cross-recessed head screw)

K. Paper dust bag

Code No. 302741

Summary of Contents for DH 24PD3













































Search results

Summary of Contents for DH 24PD3

Reviews:

Related manuals for DH 24PD3

Brands by name

Popular brands

Hitachi DH 24PD3, Technical Data And Service Manual

Search results

Summary of Contents for DH 24PD3

Reviews:

Related manuals for DH 24PD3

Brands by name

Popular brands