manualshive.com logo in svg

Hitachi DH 22PB, Technical Data And Service Manual, Page: 5 / 38

Share
Download
Hitachi DH 22PB Technical Data And Service Manual Download Page 5

--- 2 ---

4. SELLING POINTS

Push-button type forward-
reverse changeover switch

Compact body

One-push tool retainer

Class-top drilling speed
Improved resistance to grease leakage
New and powerful design

4-1. Selling Point Descriptions

4-1-1. Class-top drilling speed

The drilling speed of the Model DH 22PB is 1.8 times higher than B and 1.4 times higher than D and 1.1 times

higher than C thanks to the efficient transmission of the hammering energy.

4-1-2. Improved resistance to grease leakage

The Model DH 22PB is equipped with a sealed type ball bearing at the tip of the bearing unit while the current

Model DH 24PB is equipped with an open type ball bearing.  In addition, the clearance around the bearing is

minimized to improve the resistance to grease leakage.

4-1-3. One-push tool retainer

The tool retainer of the current Model DH 24PB needs sliding the grip to mount the bit.  The one-push tool retainer

of the Model DH 22PB eliminates the need for sliding the grip to mount the bit (sliding the grip is required at

removal of the bit).

4-1-4. Push-button type forward-reverse changeover switch

The Model DH 22PB is equipped with the push-button type forward-reverse changeover switch that is more

convenient and reliable than the lever-type switch of the current Model DH 24PB.

Summary of Contents for DH 22PB







































Reviews:

No comments