Hitachi CP-A222WN User Manual Download Page 1 | Manualshive

Page: 1 / 266

background image

1

Projector

CP-A222WN/CP-A302WN/CP-AW252WN

User's Manual (detailed)
Operating Guide

Thank you for purchasing this projector.

►Before using this product, please read all manuals for this

product. Be sure to read “

Safety Guide

” ﬁrst. After reading them, store them in a

safe place for future reference.

WARNING

• The information in this manual is subject to change without notice.

• The illustrations in this manual are for illustrative purposes. They may differ
slightly from your projector.
• The manufacturer assumes no responsibility for any errors that may appear in
this manual.
• The reproduction, transfer or copy of all or any part of this document is not
permitted without express written consent.

NOTE

Trademark acknowledgment

Various symbols are used in this manual. The meanings of these symbols are
described below.

About this manual

WARNING

CAUTION

This symbol indicates information that, if ignored, could possibly
result in personal injury or even death due to incorrect handling.

This symbol indicates information that, if ignored, could possibly
result in personal injury or physical damage due to incorrect
handling.

Please refer to the pages written following this symbol.

• Mac

®

is a registered trademark of Apple Inc.

• Windows

®

, DirectDraw

®

and Direct3D

®

are registered trademarks of Microsoft Corporation

in the U.S. and/or other countries.

• VESA and DDC are trademarks of the Video Electronics Standard Association.
• HDMI, the HDMI logo, and High-Deﬁnition Multimedia Interface are trademarks or registered

trademarks of HDMI Licensing LLC in the United States and other countries.

• Trademark PJLink is a trademark applied for trademark rights

in Japan, the United States of America and other countries and
areas.

• Blu-ray Disc

TM

and Blu-ray

TM

are trademarks of Blu-ray Disc Association.

All other trademarks are the properties of their respective owners.

NOTICE

This entry notices of fear of causing trouble.

(Type nos. CP-A222WN, CP-A222WNM, CP-A302WN, CP-A302WNM, CP-AW252WN, CP-AW252WNM)

1
2
3
...
»

Summary of Contents for CP-A222WN











































































































































































































































































Reviews:

No comments

Related manuals for CP-A222WN

Brand: 3M Pages: 9

Brand: Da-Lite Pages: 8

Brand: Panasonic Pages: 202

Brand: Cable Innovations Pages: 2

Brand: Sim2 Pages: 44

Brand: Barco Pages: 2

Brand: Retual Pages: 7

Brand: Kodak Pages: 52

LCD Pocket Projector

Brand: Merlin Pages: 4

Brand: Optoma Pages: 2

Brand: Hitachi Pages: 16

Brand: Hitachi Pages: 2

CPX268 - Portable Lcd Projector

Brand: Hitachi Pages: 2

Brand: Hitachi Pages: 1

Brand: Hitachi Pages: 2

CPX885 - XGA LCD Projector

Brand: Hitachi Pages: 5

CPX268 - Portable Lcd Projector

Brand: Hitachi Pages: 2

CPX885 - XGA LCD Projector

Brand: Hitachi Pages: 1

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands