Hitachi CMPAT04 Installation Instructions Manual Download Page 8

Page: 8 / 10

- 8 -

2. Installing the CMP401X supports

•

Fasten the two supports to the back of the plasma

display with 4 M4

12 screws.

3. Installing the display mounts

•

fasten the two display mounts to the back of the
plasma display with 6 M6

18 screws.

12 screws

(2 each)

Support fittings

1. Remove the top case of the cardboard box and

the polyethylene bag.

2. Mounting the display mount.

•

Mount the display mounting fixtures (left / right) on
the back of the plasma display unit with the bent part
facing inward, then fasten with six M6

18 screws.

18 screws

(3 each)

Display mount

The top hole of the
display mount.

The 3rd display mount
hole from the top.

The top hole of the
plasma display.

The 6th display mount
hole from the top.

2nd display mount hole
from the top.

4th hole from the top.

5th hole from the top.

Align the
protrusion of
the support
with the
outer hole.

CMP402HD

1. Remove the stand.

•

Remove the top case of the cardboard box and the
polyethylene bag.

When a stand is attached to the plasma display,
remove the four screws and detach the stand.

2. Mounting the display mount.

•

Mount the display mounting fixtures (left / right) on
the back of the plasma display unit with the bent part
facing inward, then fasten with six M6

18 screws.

Remove 4 screws.
and remove the stand.

Stand

CMP307X plasma
display

18 screws

(3 each)

2nd display mount
hole from the top.

2nd plasma display
hole from the top.

CMP307X

Display mount

(right)

Display mount

(left)

Display mount

(right)

Display mount

(left)

18 screws

(3 each)

Summary of Contents for CMPAT04











Search results

Summary of Contents for CMPAT04

Reviews:

Related manuals for CMPAT04

Brands by name

Popular brands

Hitachi CMPAT04, Installation Instructions Manual

Search results

Summary of Contents for CMPAT04

Reviews:

Related manuals for CMPAT04

Brands by name

Popular brands