-5-
-6-
When the power is ON, if a warning sound can be heard, it is a signal to indicate recharging.
Charge as soon as possible.
In order to make full use of battery performance, observe the following.
(1) If you have not used this device for three months or longer, or charge it for every
use, the number of operating times may decrease even if you fully charge at
the next time. [This is due to deactivation of the batteries (slowdown in charge
reaction) and memory effect.]
How to activate the batteries
Use the batteries until a recharge sound can be heard.
After pulling out the charger from the outlet, plug it in
again and charge for 5 hours.
Repeat 1) through 3) a few times, and the batteries are activated.
(2) In the first use:
If the number of operating times is less even after the batteries are charged for
5 hours, charge in accordance with the above method to activate the batteries.
They will return to normal.
(3) Charge the batteries at an ambient temperature in the range of 5
℃
to 35
℃
.
▼
Charge for 5 hours as is standard in accordance with
"How to charge."
▲
▼
●
●
●
Avoid use exceeding 20 minutes per day including "REFRESH".
"CLEANSING"
"MICRO-PAT"
"MOISTURIZE"
"REFRESH"
<Automatic stop>
<Automatic stop>
<Automatic stop>
(5 minutes)
(5 minutes)
(5 minutes)
(5 minutes)
●
It is recommended that you use "REFRESH" once every one or two weeks.
●
<Automatic stop>
Time to charge
Before use
When sensing anything unusual with your skin or body during
use, immediately stop using this product and consult a
dermatologist. (Cause of an accident or poor physical condition)
Remove accessories and contact lenses.
(Cause of skin trouble or poor physical condition)
2. Wash your face to remove dirt and make skin clean.
3. Attach a cotton puff to the main body. (Fig. 4)
(1) Remove the protection seal from the head.
The device will not operate unless the protection seal is removed.
(2) Place a cotton puff, and fix it with the included ring.
Use a commercially available cotton puff. However, if the cotton puff is too small or
thick may not be attachable.
The ring is directional. Attach it from straight above with the wider side of the inner
circumference placed toward the head.
Face the thinner side upward
Cotton puff
Protection seal
Do not attach the ring in the reverse direction. Be aware that the ring, if pushed with
force, will not be able to be removed.
(3) Remove the ring by pressing the thinner parts on both sides. (Fig.5)
Thinner part
4. Please observe the following so as not to damage your skin when you use the device.
(1) The maximum amount of time allowed for skin care with this device is 15 minutes
once a day in basic mode. (Avoid use exceeding 5 minutes per day in each step.)
Basic mode
Step 1
Step 2
Step 3
Step 4
This function makes your skin healthy
by using it in combination with your
regular milky lotion or sheet mask.
3
4
1
2
1. About mode selection
Step
Mode
"CLEANSING" (Pulls out fine dirt
remaining in pores.)
"MICRO-PAT" (Optimize skin
condition for moisturizing
ingredient to penetrate easily.)
"MOISTURIZE"
(Allow the toner lotion to penetrate
into cornfield layer of skin.)
"REFRESH" (Refresh the skin to
relieve stress on the skin.)
Cotton puff and cosmetics
Apply your regular toner onto a new cotton
and use.
Apply your regular toner onto the skin and
use. No cotton required.
Apply your regular toner onto a new cotton
and use.
Apply your regular milky lotion or sheet mask
to your skin for use. No cotton puff required.
You can choose "HIGH" or "LOW" as you like, but if your skin tingles, use the
device at the "LOW" level.
If you feel something unusual with your skin, stop using this device and consult a
dermatologist.
●
●
(2) Use this device on bare skin after removing makeup.
(3) Do not use this device on the same part of your skin for more than 10 seconds.
(4) Switch the potential power level between high and low by pressing the "LEVEL"
selector button according to your skin condition.
This device is equipped with a memory function for storing in memory the potential
power level ("HIGH" or "LOW") you usually use. For details, see "About the memory
function."
●
