-11-
Apply two grams of Molub Alloy 777-1 grease to the following parts in the Gear Box Ass'y
[28]
.
• Each gear tooth flank of Planet Gear (A) Set (6 pcs.)
[20]
, Pinion (B)
[21]
and Ring Gear
[22]
• Outer periphery of the six needle pins of Pinion (B)
[21]
and Pulley Shaft (A)
[23]
Apply NPC SEP 3A grease to the following parts.
• Gear tooth flank of the pinion of the Rotor Pinion Set
[14]
··············································· 0.5 g
• Inner ring of the Needle Bearing
[69]
in Blade Pulley (B)
[71]
·········································· 1 g
• Surface where the Flat Washer
[63]
contacts Blade Pulley (B)
[71]
··································· 0.2 g
• Surface where Washer (A)
[64]
contacts Blade Pulley (B)
[71]
········································· 0.2 g
• Inner circumference of the Tension Spring
[46]
····························································· 1 g
• Inner circumference of the Ring
[36]
·········································································· 0.2 g
• Whole surface of the Sleeve
[38]
··············································································· 0.5 g
• Four slotted holes on the Slide Plate
[45]
and entire circumference of four Collars
[44]
··········· 1 g
• Surface where the Protection Plate
[43]
contacts the Screw M5 x 10
[47]
························· 0.2 g
• Outer circumference of the O-ring (S-10)
[11]
····························································· 0.5 g
NOTE: Do not apply lubricant to the Blade Pulley Rubber [70].
• Tapping Screw (W/Flange) D4 x 16 (Black)
[8]
····························· 2.0±0.5 N•m {20±5 kgf•cm}
• Tapping Screw (W/Flange) D4 x 16 (Black)
[8]
for tightening the Handle Set
[2]
and the Frame
[40]
····················· 2.7±0.5 N•m {28±5 kgf•cm}
• Machine Screw (W/Washer) M3.5 x 6
[9]
···································· 0.6±0.15 N•m {6±1.5 kgf•cm}
• Tapping Screw D4 x 16
[17]
····················································· 2.0±0.5 N•m {20±5 kgf•cm}
• Tapping Screw (W/Flange) D4 x 20
[29]
······································ 2.0±0.5 N•m {20±5 kgf•cm}
• Machine Screw M6 x 16
[30]
···················································· 2.7±0.3 N•m {28±3 kgf•cm}
• Tapping Screw (W/Flange) D3 x 20
[35]
······································ 1.4±0.4 N•m {14±4 kgf•cm}
• Lock Nut M5
[48]
··································································· 3.4±0.7 N•m {35±7 kgf•cm}
• Bearing Pin (B)
[55]
································································ 3.4±0.7 N•m {35±7 kgf•cm}
• Hex. Socket Hd. Bolt (W/Washers) M5 x 16
[60]
··························· 5.9±1.5 N•m {60±15 kgf•cm}
• Hex. Socket Hd. Bolt M6 x 16
[65]
············································· 9.8±2.0 N•m {100±20 kgf•cm}
• Tapping Screw (W/Flange) D4 x 20
[76]
······································ 2.0±0.5 N•m {20±5 kgf•cm}
Lubrication points and type of lubricant
Screw tightening torque
