Hitachi BE-IR30 Operation Manual Download Page 11 | Manualshive

Page: 11 / 26

background image

8. Installation

BE-IR30 / 31

10

When installing the camera in a housing or unit of equipment, secure with two M2 screws

inserted into the 2.5 mm diameters holes of the SENS board base plate.

1. Use the SENS board holds to install the camera. Avoid using only the Main board,

due to risk of damage to the board connector.

2. Avoid unnecessary stress on the printed board when engaging and disengaging the

connectors.

3. The screws securing the base plate and SENS board protrude a maximum of 2 mm

from the base plate. Observe these screws do not contact the housing or installed

equipment.

Two 2.5 mm Dia.

SENS board

Notes :

«
...
9
10
11
12
13
...
»

Summary of Contents for BE-IR30



























Reviews:

No comments

Related manuals for BE-IR30

Brand: GE Pages: 7

Brand: Wansview Pages: 28

Brand: D-Link Pages: 2

DCS-1130 - mydlink-enabled Wireless N Network...

Brand: D-Link Pages: 58

Brand: Velleman Pages: 3

iMEGAPRO IPR7922E

Brand: Lilin Pages: 12

Brand: Alpha Networks Pages: 11

Brand: jablotron Pages: 2

Brand: Hanwha Vision Pages: 15

Brand: Arec Pages: 68

Brand: THIESEN Pages: 2

Brand: G-Force Pages: 2

Brand: KAYS TECH Pages: 11

Brand: M-system Pages: 2

DCC-580D Series

Brand: D-MAX Pages: 24

Brand: ProVisual Pages: 7

Brand: Zee Pages: 13

Brand: SAINT-GOBAIN Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands