Hitachi 57T600 Operating Manual Download Page 41

Page: 41 / 80

USING YOUR REMOTE
TO CONTROL ADDITIONAL AUDIO EQUIPMENT

NOTES:

If your Audio component cannot be operated after

performing the above procedures, your Audio
component’s code has not been precoded into the
remote.

In the unlikely event that your Audio component cannot be

operated after performing the above procedures, please
consult your Audio equipment operating guide.

The remote control will remember the codes you have

programmed until the batteries are removed from the
remote control. After replacing the batteries repeat the
entire programming procedure as stated above.

CD, TAPE, AMP Buttons

These buttons allow the remote to control your Audio
equipment by setting it to Audio mode.

PRECODED AUDIO Buttons

These buttons transmit the chosen precoded Audio
component codes.

EXCLUSIVE TV Buttons

These buttons are for operating the TV.

POWER

VCR

CBL

DVD

VIDEO

SOURCE WIZARD

STB

SVC

VID

VID 3

VID 4

VID

MY AUDIO EQUIPMENT CODE IS:

NOTE:

Refer to instruction manual of the Audio equipment for operation of the buttons exclusively for the Audio equipment.

CD ________

TAPE ________

AMP/RCVR ________

THE

REMO

CONTR

Summary of Contents for 57T600

















































































Search results

Summary of Contents for 57T600

Reviews:

Related manuals for 57T600

Brands by name

Popular brands

Hitachi 57T600, Operating Manual

Search results

Summary of Contents for 57T600

Reviews:

Related manuals for 57T600

Brands by name

Popular brands