Hitachi 3HRNM1Q Installation & Maintenance Manual Download Page 26

Page: 26 / 36

Main Switch

Remote
Control Switch
(Option)

Outdoor Unit

Indoor Unit No.1

Indoor Unit No.2

Indoor Unit No.3

Indoor Unit No.4

Earth
Wiring

Remote Control
Switch Cable

(Field Supplied)

Shielded Twist-Pair Cable 0.75mm

x 2

This cable dose not need any polarity.

Do not apply an excessively high
voltage to this cable. (Rated Voltage: 5V)

Control Cable

Power Source Cable

Pay an attention to the phase
of power source when wiring.

Fig. 6.2 Wiring Connection

Install an ELB in the power source.
If ELB is not used, it will cause electric shock or fire
at the worst.

The tightening torque of each screw shall be as
follows.

M4:

1.0 to 1.3 N-m

M5:

2.0 to 2.5 N-m

M6:

4.0 to 5.0 N-m

M8:

9.0 to 11.0 N-m

M10:

18.0 to 23.0 N-m

Keep the above tightening torque when wiring work.

L2 L3 N

L1 L2

N
Mp

1 2 A B

Outdoor Unit

Indoor Unit No.1

Main Switch

Remote
Control Switch
(Option)

Remote Control
Switch Cable
(Field Supplied)

Shielded Twist-Pair Cable 0.75mm

x 2

This cable dose not need any polarity.
Do not apply an excessively high
voltage to this cable. (Rated Voltage: 5V)

Shielded Twist-Pair Cable 0.75mm

x 2

This cable dose not need any polarity.
Do not apply an excessively high
voltage to this cable. (Rated Voltage: 12V)

Control Cable

Power Source Cable

Pay an attention to the phase
of power source when wiring.

Remote
Control Switch
(Option)

Earth
Wiring

L1 L2

N
Mp

1 2 A B

Indoor Unit No.2

ELB

1 2

L1 L2

N
Mp

1 2 A B

Indoor Unit No.3

L1 L2

N
Mp

1 2 A B

Indoor Unit No.4

Remote
Control Switch
(Option)

Fig. 6.5 Wiring Connection ( 380V 3N 60Hz)

Fig. 6.4 Wiring Connection ( 380-415V 3N 50Hz)

L2 L3 N

L1 L2

N
Mp

1 2 A B

Outdoor Unit

Indoor Unit No.1

Main Switch

Remote
Control Switch
(Option)

Remote Control
Switch Cable
(Field Supplied)

Shielded Twist-Pair Cable 0.75mm

x 2

This cable dose not need any polarity.
Do not apply an excessively high
voltage to this cable. (Rated Voltage: 5V)

Shielded Twist-Pair Cable 0.75mm

x 2

This cable dose not need any polarity.
Do not apply an excessively high
voltage to this cable. (Rated Voltage: 12V)

Control Cable

Power Source Cable

Pay an attention to the phase
of power source when wiring.

Remote
Control Switch
(Option)

Earth
Wiring

L1 L2

N
Mp

1 2 A B

Indoor Unit No.2

ELB

1 2

L1 L2

N
Mp

1 2 A B

Indoor Unit No.3

L1 L2

N
Mp

1 2 A B

Indoor Unit No.4

Remote
Control Switch
(Option)

220-240V 50Hz)

Main Switch

Remote
Control Switch
(Option)

Outdoor Unit

Indoor Unit No.1

Indoor Unit No.2

Indoor Unit No.3

Indoor Unit No.4

Earth
Wiring

Remote Control
Switch Cable

(Field Supplied)

Shielded Twist-Pair Cable 0.75mm

x 2

This cable dose not need any polarity.

Do not apply an excessively high
voltage to this cable. (Rated Voltage: 5V)

Control Cable

Power Source Cable

Pay an attention to the phase
of power source when wiring.

Main Switch

Remote
Control Switch
(Option)

Outdoor Unit

Indoor Unit No.1

Indoor Unit No.2

Indoor Unit No.3

Indoor Unit No.4

Earth
Wiring

Remote Control
Switch Cable
(Field Supplied)

Shielded Twist-Pair Cable 0.75mm

x 2

This cable dose not need any polarity.
Do not apply an excessively high
voltage to this cable. (Rated Voltage: 5V)

Shielded Twist-Pair Cable 0.75mm

x 2

This cable dose not need any polarity.
Do not apply an excessively high
voltage to this cable. (Rated Voltage: 12V)

Control Cable

Power Source Cable

Pay an attention to the phase
of power source when wiring.

Main Switch

Remote
Control Switch
(Option)

Outdoor Unit

Indoor Unit No.1

Indoor Unit No.2

Indoor Unit No.3

Indoor Unit No.4

Earth
Wiring

Remote Control
Switch Cable
(Field Supplied)

Shielded Twist-Pair Cable 0.75mm

x 2

This cable dose not need any polarity.
Do not apply an excessively high
voltage to this cable. (Rated Voltage: 5V)

Shielded Twist-Pair Cable 0.75mm

x 2

This cable dose not need any polarity.
Do not apply an excessively high
voltage to this cable. (Rated Voltage: 12V)

Control Cable

Power Source Cable

Pay an attention to the phase
of power source when wiring.

Fig. 6.3 Wiring Connection 220V 60Hz)

Shielded Twist-Pair Cable 0.75mm x 2
This cable dose not need any polarity.
Do not apply an excessively high
voltage to this cable. (Rated Voltage: 12V)

FUSE

Switch

FUSE

Switch

FUSE

Switch

FUSE

Switch

220-240V~/50HZ

220V~/60HZ

220-240V~/50HZ

220V~/60HZ

380-415V 3N ~/50HZ

380V 3N~/60HZ

Install an ELB in the power source.
If ELB is not used, it will cause electric shock or fire
at the worst.

The tightening torque of each screw shall be as
follows.

M4:

1.0 to 1.3 N-m

M5:

2.0 to 2.5 N-m

M6:

4.0 to 5.0 N-m

M8:

9.0 to 11.0 N-m

M10:

18.0 to 23.0 N-m

Keep the above tightening torque when wiring work.

Install an ELB in the power source.
If ELB is not used, it will cause electric shock or fire
at the worst.

The tightening torque of each screw shall be as
follows.

M4:

1.0 to 1.3 N-m

M5:

2.0 to 2.5 N-m

M6:

4.0 to 5.0 N-m

M8:

9.0 to 11.0 N-m

M10:

18.0 to 23.0 N-m

Keep the above tightening torque when wiring work.

Install an ELB in the power source.
If ELB is not used, it will cause electric shock or fire
at the worst.

The tightening torque of each screw shall be as
follows.

M4:

1.0 to 1.3 N-m

M5:

2.0 to 2.5 N-m

M6:

4.0 to 5.0 N-m

M8:

9.0 to 11.0 N-m

M10:

18.0 to 23.0 N-m

Keep the above tightening torque when wiring work.

Install an ELB in the power source.
If ELB is not used, it will cause electric shock or fire
at the worst.

The tightening torque of each screw shall be as
follows.

M4:

1.0 to 1.3 N-m

M5:

2.0 to 2.5 N-m

M6:

4.0 to 5.0 N-m

M8:

9.0 to 11.0 N-m

M10:

18.0 to 23.0 N-m

Keep the above tightening torque when wiring work.

Install an ELB in the power source.
If ELB is not used, it will cause electric shock or fire
at the worst.

The tightening torque of each screw shall be as
follows.

M5:

2.0 to 2.5 N-m

M6:

4.0 to 5.0 N-m

M8:

9.0 to 11.0 N-m

M10:

18.0 to 23.0 N-m

Keep the above tightening torque when wiring work.

Install an ELB in the power source.
If ELB is not used, it will cause electric shock or fire
at the worst.

The tightening torque of each screw shall be as
follows.

M5:

2.0 to 2.5 N-m

M6:

4.0 to 5.0 N-m

M8:

9.0 to 11.0 N-m

M10:

18.0 to 23.0 N-m

Keep the above tightening torque when wiring work.

Install an ELB in the power source.
If ELB is not used, it will cause electric shock or fire
at the worst.

The tightening torque of each screw shall be as
follows.

M5:

2.0 to 2.5 N-m

M6:

4.0 to 5.0 N-m

M8:

9.0 to 11.0 N-m

M10:

18.0 to 23.0 N-m

Keep the above tightening torque when wiring work.

Summary of Contents for 3HRNM1Q





































Search results

Summary of Contents for 3HRNM1Q

Reviews:

Brands by name

Popular brands

Hitachi 3HRNM1Q, Installation & Maintenance Manual

Search results

Summary of Contents for 3HRNM1Q

Reviews:

Brands by name

Popular brands