manualshive.com logo in svg

Hitachi 3HRNM1Q, Installation & Maintenance Manual

Share
Download
Hitachi 3HRNM1Q Installation & Maintenance Manual Download Page 14

4.3

Service Space

Install the outdoor unit with a sufficient space around the outdoor unit for operation and maintenance as
shown below.

(1) Upper Side is Open.

 Installation

Single

Upper Side is Open

 Installation

Single

 Installation

Multiple

Upper Side is Open

Fig. 4.1  Installation Space 

Keep a  distance of 100mm between service cover and wall.

The dimension in "(  )" is for the model of 4  H   P    and 5H   P  .

Above of two sides of 

 the unit is open.

(Occasion of obstacles in 

the obverse side of the units) 

Keep a distance of more than 100mm between other units.

Obstacles in Above

When obstacles is in above ,it is should be ensured that the distance between the top of

units and obstacles is more than 500mm, besides the space for installation and maintenance 

is satisfied. 

7

(unit:mm)

The dimension in "(  )" is for the model of 4  H   P    and 5H   P  .

The dimension in "(  )" is for the model of 4  H   P    and 5H   P  .

Summary of Contents for 3HRNM1Q





































Reviews:

No comments

Brands by name

Popular brands

Load more brands