Hisense HPA27C Use And Installation Instructions Download Page 9

Safety precautions

 8

CAUTION

     instructions concerning the equipment that is at hand and shall be suitable for
     the recovery of flammable refrigerants. 
     In addition, a set of calibrated weighing scales shall be available and in good
     working order.   
     Hoses shall be complete with leak-free disconnect couplings and in good
     condition. 
     Before using the recovery machine, check that it is in satisfactory working
     order, has been properly maintained and that any associated electrical
     components are sealed to prevent ignition in the event of a refrigerant release. 
     Consult manufacturer if in doubt.
     The recovered refrigerant shall be returned to the refrigerant supplier in the
     correct recovery cylinder, and the relevant Waste Transfer Note arranged. 
     Do not mix refrigerants in recovery units and especially not in cylinders. 
     If compressors or compressor oils are to be removed, ensure that they have
     been evacuated to an acceptable level to make certain that flammable
     refrigerant does not remain within the lubricant. 
     The evacuation process shall be carried out prior to returning the compressor
     to the suppliers. 
     Only electric heating to the compressor body shall be employed to accelerate
     this process.    
     When oil is drained from a system, it shall be carried out safely.    

CAUTION

     When moving or relocating the air conditioner, consult experienced service
     technicians for disconnection and reinstallation of the unit.
     Do not place any other electrical products or household belongings under
     indoor unit or outdoor unit. Condensation dripping from the unit might get them
     wet, and may cause damage or malfunction of your property.
     Do not use means to accelerate the defrosting process or to clean, other than 
     those recommended

 

by

 

the

 

manufacturer

.

     The appliance shall be stored in a room without continuously operating ignition
     sources(for example, open flames, an operating gas appliance or an operating
     electric heater)

.

        

     Do not pierce or burn

.

     Be aware that refrigerants may not contain an odor

.

   To keep ventilation openings clear of obstruction. 

     The appliance shall be stored in a well-ventilated area where the room size
     corresponds to the room area as specified for operation.
     The appliance shall be stored in a room without continuously operating open
     flames (for example an operating gas appliance) and ignition sources (for 
     example an operating electric heater).  
     The appliance shall be stored so as to prevent mechanical damage from
     occurring.

Summary of Contents for HPA27C
































Reviews: