background image

OPERATIONS TO BE PERFORMED WHEN SUBSTITUTING THE INJECTORS

If the injectors are not supplied they can be obtained from the “Service Centre”.

 

 Remove the gratings and the burner covers;

 

Using a wrench, substitute the nozzle injectors;

“J” (left Fig. 13) with those most suitable for the kind of gas for which it is to be used (see 
Injector table).

The burners are conceived in such a way so as not to require the regulation of the primary air.

REGULATING THE BURNER MINIMUM SETTING

When switching from one type of gas to another, the minimum flow rate must also be correct 
the flame should not go out even when passing suddenly from maximum to minimum flame. To 
regulate the flame follow the instructions below:

1.Light the burner

2.Set the cock valve to minimum

On gas valves provided with adjustment screw in the centre of the shaft (fig.14)

Using a screwdriver with max. diameter 3 mm, turn the screw

inside the tap until the correct setting is obtained.

On gas valves provided with adjustment screw on the valve body (fig.15):

Turn the screw “A” to the correct setting with a screwdriver.Normally for G30 gas, fully tighten 
the adjustment screw.

LUBRICATION OF THE GAS TAPS

If the gas tap becomes stiff, it is necessary to dismount it accurately clean it with gasoline and 
spread a bit of special grease resistant to high temperatures on it.

The operations must be executed by a qualified technician.

10

Summary of Contents for HHU60GASS


















Reviews: