manualshive.com logo in svg

Hirschmann OCTOPUS 16M-Train-BP, User Manual

Share
Download
Hirschmann OCTOPUS 16M-Train-BP User Manual Download Page 36

36

Installation OCTOPUS 8M/16M/24M/OS32

Release 16 06/2018

7.2

Dimension drawings

Figure 6: Measurements for the following devices:

- OCTOPUS 8M (shown in the figure)
- OCTOPUS 8M-Train
- OCTOPUS 8M-Train-BP
- OCTOPUS 8M-6PoE
- OCTOPUS 8M-8PoE

b. Relevant for North America: max. 0.5 A, resistive load.

c. Temperature of the ambient air at a distance of 2 in (5 cm) from the device

d. Remove the provided transport protection caps and the transport protection screws from the 

device. Seal unused sockets and plugs with the type of protection screws which you can 

order separately.

e. Remove the provided transport protection caps and the transport protection screws from the 

device. Seal unused sockets and plugs with the type of protection screws which you can 

order separately.

f.

To preserve the suitability of your device for IP65/67, proceed as follows: Remove all 

provided transport protection caps and transport protection screws. Seal unused sockets 

and plugs with the type of protection screws which you can order separately.

Summary of Contents for OCTOPUS 16M-Train-BP

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands