manualshive.com logo in svg

HiP T Series, Instructions - Parts Manual, Page: 21 / 36

Share
Download
HiP T Series Instructions - Parts Manual Download Page 21

Repair - Pneumatic Motor

3A6823A

21

10. Lubricate and install the o-ring (209) in the bottom 

cover (201).

11. Install the piston bumper (228) on the bottom 

cover (201).

12. Carefully place the bottom cover (201) on the cylin-

der (211), sliding the plunger (206) through the seal 
stack. The manifold surfaces of the top and bottom 
covers must align. Be sure the shield (212) is in the 
groove on both the top and bottom covers. See F

IG

. 

10.

13. Install the tie bolts (210) hand tight. See the figure 

on page 26.

14. Install two gaskets (214) on the manifold (215), and 

install the manifold. Torque bolts to 95-105 in-lb 
(11-12 N•m). 

15. Align the pneumatic valve gasket (216) on the mani-

fold (215), then attach the pneumatic valve (217).

16. Tighten the bolts (210) halfway. Work in a 

criss-cross pattern while tightening the tie bolts. 
Check that the shield remains in the grooves on 
both covers. Continue tightening the bolts in pattern 
and torque to 25-30 ft-lb (34-40 N•m).

17. Lubricate and install the pilot valves (219) in the top 

and bottom covers. Torque to 95-105 in-lb (11-12 
N•m).

18. See 

Reconnect the Pneumatic Motor

 on page 22.

F

IG

. 9

239

233

233

239

240

203

239

239

239

233

233

204

202

201

 Stack for models T6003 and T7505 only

Stack for all models except T6003 and T7505

U-cup up

U-cup up

U-cup
down

U-cup down

U-cup up

F

IG

. 10

201

206

211

213

212

Summary of Contents for T Series





































Reviews:

No comments