Hioki MR8827 Instruction Manual Download Page 339

Page: 339 / 436

334

Operate the Instrument Remotely and Acquire Data Using the Model 9333 LAN Communicator

About headers

The response to a

[:FUNCTION?]

query command from the PC differs

according to the header setting.

[On]

..............

[:FUNCTION MEM]

[Off]

..............

[MEM]

About port numbers

Specify only the most significant 3

digits of the 4-digit port number.

If you specify “880x,” port number

8802 will be used. (p. 333)

16.8

Operate the Instrument Remotely and Acquire

Data Using the Model 9333 LAN Communicator

The Model 9333 LAN Communicator, which is the optional communication program for PCs, allows

the PC to control the instrument remotely and to store data directly. Additionally, Model 9333 enables

waveforms to be printed from a printer connected to the PC.

Procedure

Set the LAN Communicator.

Use the LAN Communicator.

Off

Do not use the LAN Communicator.

Set the data collection server

Specify the IP address of the PC on which Model 9333 LAN

Communicator is running to communicate with the instrument.

The IP address is required to acquire data using the Model

9333 LAN Communicator.

If necessary, set “

LAN:\

” as the save destination on the

[File

Save]

sheet, and set

[LAN]

as the output destination of the

Print Key operation and the auto-print setting.

Apply the settings.

Move the cursor to

[Reset].

Select

[Reflect Set].

The “LAN was reconnected” message will appear at the

bottom of the screen.

For the settings of the Model 9333 LAN Communicator, see the instruction manual of Model 9333 LAN

Communicator.

Summary of Contents for MR8827




















































































































































































































































































































































































































































Search results

Summary of Contents for MR8827

Reviews:

Related manuals for MR8827

Brands by name

Popular brands

Hioki MR8827, Instruction Manual

Search results

Summary of Contents for MR8827

Reviews:

Related manuals for MR8827

Brands by name

Popular brands