Hioki MR8827 Instruction Manual Download Page 338

Page: 338 / 436

333

Controlling the Instrument with Command Communications (LAN/USB)

16.7

Controlling the Instrument with Command

Communications (LAN/USB)

You can control the instrument remotely via the communications interface (LAN or USB).

• For details, see the Communication Command Instruction Manual on the supplied application disc.

• Before using command communications, the LAN settings or USB settings and connection must have

been configured properly.

About LAN, refer to ““16.1” (p. 310); USB“16.6” (p. 328).

CAUTION

In an environment where noise from inverters or similar devices is present, errors

may occur when controlling the instrument remotely. Take care to ensure that the

environment is not subject to excessive noise.

Setting Details

Delimiter

The Delimiter item specifies LF or CR+LF as the newline delimiter in command response

messages. The instrument understands both settings: LF or CR+LF.

Header

Use for control of communications commands.

The Header item specifies whether to prefix headers to command response messages.

For more information about commands, refer to the Communications operation manual on the

supplied CD.

Command Port

(Port number) (LAN

only)

The instrument uses the TCP/IP protocol for communications. TCP/IP allows communicating

devices to establish multiple connections, which are distinguished by port number. By default

the instrument uses port numbers 8800 to 8809.

•8800 to 8801 reserved

•8802 (instrument is server): For communications command control

•

8803 to 8809 reserved

Normally these ports do not need to be changed. You can change them if certain ports cannot

be used for security reasons, or if certain ports are not available on the communicating PC.

Set only the most significant three digits. The least significant digit (0 to 9) is used by the

instrument, or reserved for use by the instrument.

16.7.1

Settings on the Instrument

Set items related to command communications.

Procedure

Press the

SYSTEM

key to open the System screen, and then select the

[Interface]

sheet.

Set the delimiter.

Move the cursor to

[Delimiter].

Send character code 0x0a.

CR+LF

Send character codes 0x0d and 0x0a.

Select header settings.

Move the cursor to

[Header].

Off

Do not add a header to response data.

Add a header to response data.

Set the communications command port. (LAN only)

Move the cursor to

[Port Number]

and enter the port number.

Connect to a PC

Summary of Contents for MR8827




















































































































































































































































































































































































































































Search results

Summary of Contents for MR8827

Reviews:

Related manuals for MR8827

Brands by name

Popular brands

Hioki MR8827, Instruction Manual

Search results

Summary of Contents for MR8827

Reviews:

Related manuals for MR8827

Brands by name

Popular brands