Hioki MR8827 Instruction Manual Download Page 179

Page: 179 / 436

174

Detailed Settings for Modules

• The calibration time is approximately 150 ms. During this period measurement is not performed.

• If synchronization between channels is performed, a signal to stop integration is sent to each module

when measurement is started and the wait process is performed until the first integration finishes.

The wait time required for this process is (10 ms + integration time*).

* The integration time varies depending on the NPLC setting.

If synchronization is not performed, the above wait time will also be required for measurement

performed immediately after the settings of the Model MR8990 Digital Voltmeter Unit are changed.

However, there will be no wait time when measurement is performed with the same settings.

• When this is set to

[Off]

(Default setting), perform calibration manually.

Refer to “2.8 Perform Calibration (When Model MR8990 is installed)” (p. 48).

8.10.9 Setting Model U8974 High Voltage Unit

Refer to: “To Open

[Each Ch]

and Make a Channel Selection” (p. 164)

Mode

Switches between voltage measurement and RMS measurement.

Voltage measurement (Default setting)

RMS

RMS measurement

Response

The response time for RMS measurement can be set to three speeds: Fast, Normal

and Slow.

The response time can be set to

[Slow]

to stabilize the measured value when the

frequency is low or when severe fluctuations are present.

Fast

Response time is set to 150 ms.

Normal

Response time is set to 500 ms. (Default setting)

Slow

Response time is set to 2.5 s.

Summary of Contents for MR8827




















































































































































































































































































































































































































































Search results

Summary of Contents for MR8827

Reviews:

Related manuals for MR8827

Brands by name

Popular brands

Hioki MR8827, Instruction Manual

Search results

Summary of Contents for MR8827

Reviews:

Related manuals for MR8827

Brands by name

Popular brands