Hioki IM7580A-1 Communication Instruction Manual Download Page 19

Page: 19 / 23

RS-232C Connection and Settings (when the Z3001 is connected)

2.5 RS-232C Connection and Settings

(when the Z3001 is connected)

Connecting the RS-232C Cable

Connect the RS-232C cable to the RS-232C connector.

(Recommended cable: 9637 RS-232C cable)

Male 9-pin D-sub
#4-40 attaching
screws

To connect the instrument to a controller (DTE)

use a crossover cable compatible

with the connectors on both the instrument and the controller.

The I/O connector is a DTE (Data Terminal Equipment) configuration.

1 2 3 4 5

6 7 8 9

Connector (D-sub)

Pin No.

Interchange Circuit

Name

CCITT

Circuit No.

EIA

Abbreviation

JIS

Abbreviation

Common

Abbreviation

Unused

Received Data

104

RxD

Transmitted Data

103

TxD

Data Terminal Ready

108/2

DTR

Signal Ground

102

GND

Unused

Example: Connecting to a DOS/V PC

Specification: D-sub 9-pin female and female connector

reverse connection

Summary of Contents for IM7580A-1
























Search results

Summary of Contents for IM7580A-1

Reviews:

Brands by name

Popular brands

Hioki IM7580A-1, Communication Instruction Manual

Search results

Summary of Contents for IM7580A-1

Reviews:

Brands by name

Popular brands