Hino 238 Workshop Manual Download Page 539

Page: 539 / 919

ENGINE CONTROL SYSTEM (J08E)

4–1316

DTC: U010C

EN01H16F01030F03001161

U010C: VNT actuator CAN communication error

INFORMATION

1. Technical description

•

–

<Description of malfunction>

•

CAN communication between the VNT controller and engine ECU is interrupted.

2. DTC set condition

(1) DTC detection condition

•

Starter switch is ON.

•

Engine ECU power supply voltage is in the range of 11 V to 16 V.

(2) Judgement criteria

•

When CAN data from the engine ECU cannot be received by the VNT controller for at least 1 second.

•

When the CAN data sent from the engine ECU exceeds its range.

•

When CAN data from the VNT controller is not received by the engine ECU for at least 3 seconds.

3. Reset condition

•

After normal operation is restored and the starter switch is turned OFF.

4. Indication, warning or system control regulation when the DTC is set.

•

MIL: ON

•

Diag lamp: OFF

•

Engine output is restricted.

5. Symptoms on the vehicle when the DTC is set

<Symptoms on the vehicle due to backup control (fail safe function)>

•

Engine output is insufficient.

NOx

sensor 2

Common rail

CAN J/C3

Common rail

CAN J/C1

NOx

sensor 1

%JZ

%JU

%JV

%JQ

(7)

(6)

(3)

(2)

%KL

(7)

%KM

(6)

%JX

(8)

%JS

(5)

LEC

LED

(CANL)

(CANH)

%JW

(4)

%JR

(1)

LE8

LE9

(CANL)

(CANH)

DEF

Sensor

%KN

(8)

%KP

(5)

LEJ

LEK

(CANL)

(CANH)

%KE

(3)

%KF

(2)

BCU

%KG

(4)

%KH

(1)

LJL

LJK

(CAL0)

(CAH0)

Engine

ECU

CAN TMN

EGR

Controller

VNT

Controller

L4R

(EGRH)

L4S

(EGRL)

Twist

KV8

(VNTH)

KV9

(VNTL)

LEY

(CAH0)

LEZ

(CAL0)

KRG

(CA2H)

F2F

(CANL)

F2E

(CANH)

%J8

(L4R)

%J5

(L4S)

%J3

(KV8)

%J2

(KV9)

%J1

(K6W)

%J4

(K6V)

%J6

(LEZ)

#AP

#AN

%J7

(LEY)

(LEZ)

(LEY)

KRH

(CA2L)

Twist

K6W

(CANL)

K6V

(CANH)

Twist

#CP

#CQ

Twist

#SF

#SD

DCU

SAPH16F010301032

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 238

Reviews:

Related manuals for 238

Brands by name

Popular brands

Hino 238, Workshop Manual

Search results

Summary of Contents for 238

Reviews:

Related manuals for 238

Brands by name

Popular brands