![background image](http://html1.mh-extra.com/html/hilti/xbt-4000-a/xbt-4000-a_operating-instructions-manual_2135535020.webp)
7. Operation
-CAUTION-
– The tool and the drilling operation emit noise. Exces-
sive noise may damage the hearing. Wear ear protec-
tion.
– The drilling procedure may cause the material to splin-
ter. Splintering material may cause injury to the body,
respiratory passages and the eyes. Wear eye protec-
tion, breathing protection and a safety helmet.
– The chuck has rough surface. A rotating chuck can
cause hand injuries. Use protective gloves.
7.1 Quick-release chuck
7.1.1 Opening the quick-release chuck
1. Open the quick-release chuck by turning the sleeve
until the insert tool can be fitted or removed.
7.1.2 Closing the quick-release chuck
1. Fit the insert tool into the chuck.
2. Tighten the chuck by turning the chuck sleeve firmly.
16
en
6. Before use
A new battery must be charged correctly for the first
time before use:
– charged normally for 24 hours with the SFC 7/18 H
charger, or
– charged for 12 hours using the conditioning function
of the SFC 7/18, C7/24 or TCU 7/36 charger. This will
ensure that the cells form correctly. Incorrect initial
charging may have a permanent, negative effect on
battery capa city.
-NOTE-
– The tool may be used only with SFB 185 batteries.
– Battery performance drops at low temperatures.
– Batteries should be stored at room temperature.
– Never store batteries where they are exposed to the
heat of the sun, on a radiator, behind a motor vehicle
windscreen or at a window.
– Never use the battery until the cells become fully dis-
charged. Change to the second battery as soon as a
drop in performance is noticed and recharge the bat-
tery immediately so that it is ready for re-use.
– Use TX-BT 4/7-80 /110 / 150 step drill bits only.
Since it cannot be charged via the belt adapter, always
insert the battery straight into the charger.
7.2 Switching on and off
Switch the drill off to avoid damage if a jammed bit
stalls the motor for more than 2 or 3 seconds.
1. The speed can be varied continuously between 0
and the maximum by pressing the ON/OFF switch
slowly.
7.3 Selecting sustained operation
The lockbutton for sustained operation can be used to
keep the motor running continuously at the optimum
speed with appropriate cooling.
Switch the drill off to avoid damage if a jammed bit
stalls the motor for more than 2 or 3 seconds.
1. Press the ON/OFF switch and hold it in.
2. Press the lockbutton.
3. Release the ON/OFF switch.
4. Release the lockbutton.
7.4 Ending sustained operation
1. Press the ON/OFF switch fully. The lockbutton will
5.2.6 Battery tool use and care
a)
Ensure that the outer surfaces of the battery are
clean and dry before inserting it in the corresponding
charger.
b)
Check that the battery is securely attached to the
tool.
A falling battery could injure you or other per-
sons.
c)
The batteries must be disposed of correctly on
reaching the end of their life (see section 10).
d)
Do not charge or continue to use damaged batter-
ies (e.g. batteries with cracks, broken parts, bent
or pushed-in and/or pulled-out contacts).
Printed: 08.07.2013 | Doc-Nr: PUB / 5071408 / 000 / 01
Summary of Contents for XBT 4000-A
