![background image](http://html.mh-extra.com/html/hilti/te-7/te-7_operating-instructions-manual_2135459023.webp)
that the workplace is well ventilated. The use of a
dust mask of filter class P2 is recommended. Fol-
low national requirements for the materials you
want to work with.
5.2.2 Power tool use and care
a)
Secure the workpiece. Use clamps or a vice to
secure the workpiece.
The workpiece is thus held
more securely than by hand and both hands remain
free to operate the power tool.
b)
Check that the insert tools used are compatible
with the chuck system and that they are secured
in the chuck correctly.
c)
Switch the power tool off and unplug the supply
cord in the event of a power failure or interruption
in the electric supply.
This will prevent accidental
restarting when the electric power returns.
5.2.3 Electrical safety
a)
Before beginning work, check the working area
(e.g. using a metal detector) to ensure that no
concealed electric cables or gas and water pipes
are present.
External metal parts of the power tool
may become live, for example, when an electric cable
is damaged accidentally. This presents a serious risk
of electric shock.
b)
Check the power tool’s supply cord at regular
intervals and have it replaced by a qualified spe-
cialist if found to be damaged. If the power tool’s
supply cord is damaged it must be replaced with
a specially-prepared supply cord available from
Hilti Customer Service. Check extension cords
at regular intervals and replace them if found to
be damaged. Do not touch the supply cord or
extension cord if it is damaged while working.
Disconnect the supply cord plug from the power
outlet.
Damaged supply cords or extension cords
present a risk of electric shock.
c)
Dirty or dusty power tools which have been used
frequently for work on conductive materials
should be checked at regular intervals at a Hilti
Service Center.
Under unfavorable circumstances,
dampness or dust adhering to the surface of
the power tool, especially dust from conductive
materials, may present a risk of electric shock.
d)
When working outdoors with an electric tool
check to ensure that the tool is connected to the
electric supply by way of a ground fault circuit
interrupter (RCD) with a rating of max. 30 mA
(tripping current).
Use of a ground fault circuit
interrupter reduces the risk of electric shock.
e)
Use of a ground fault circuit interrupter (RCD
residual current device) with a maximum tripping
current of 30 mA is recommended.
5.2.4 Work area safety
a)
Ensure that the workplace is well lit.
b)
Ensure that the workplace is well ventilated.
Ex-
posure to dust at a poorly ventilated workplace may
result in damage to the health.
c) There is a risk of injury when the drill bit breaks
through the object in which the hole is being drilled.
Implement the appropriate safety measures at the
rear of the object
. Parts breaking away could fall out
and / or fall down and injure other persons.
5.2.5 Personal protective equipment
The user and any other persons in the vicinity must
wear suitable eye protection, a hard hat, ear protec-
tion, protective gloves and breathing protection while
the tool is in use.
6 Before use
6.1 Fitting the side handle
2
CAUTION
Remove the depth gauge from the side handle in order
to avoid injury.
1. Disconnect the supply cord plug from the power
outlet.
2. Release the side handle clamping band by turning
the handle counterclockwise.
3. Slide the side handle clamping band over the chuck
and onto the cylindrical section at the front end of
the power tool.
4. Pivot the side handle into the desired position.
5.
CAUTION Check that the clamping band is en-
gaged in the groove provided on the power tool.
Secure the side handle by turning the grip clockwise.
6.2 Use of extension cords and generators or
transformers
Please refer to the “Description” section.
en
19
Printed: 08.07.2013 | Doc-Nr: PUB / 5071130 / 000 / 01