12
en
The tool is designed for the following uses:
Use
Required insert tools
Diameter range
TE 2 / TE 2-E / TE 2-S / TE 2-M:
Hammer drilling in concrete,
Drill bits with TE-C connection end Drilling in concrete:
masonry and natural stone
– Short hammer drill bits
Anchor holes of 4–22 mm dia.
– Long hammer drill bits
Through holes of 4–22 mm dia.
TE 2-S:
Drilling with precision
Drill bits with TE-C connection end Drilling in brittle materials:
hammering action in perforated
– TE-C hammer drill bits
Anchor holes of 4–22 mm dia.
brick, tiles and marble
– Thin-barrel core bits
Cutting sockets of 25–68 mm dia.
TE 2 / TE 2-E / TE 2-S:
Drilling in wood, drywall panels
Quick-release chuck with TE-C adaptor for insert
and metal
tools with cylindrical shank or hexagonal shank
for rotary-only drilling
Wood drill bits
4–20 mm dia.
Metal drill bits
3–13 mm dia.
Hole saws
25–68 mm dia.
TE 2-M:
Drilling in wood, drywall panels,
Interchangeable quick-release chuck for
tiles and metal
insert tools with cylindrical shank or hexagonal
shank for rotary-only drilling:
Wood drill bits
4–10 mm dia. in 2nd gear
10–20 mm dia. in 1st gear
Metal /stepped drill bits
3– 8 mm dia. in 2nd gear
8–13 mm dia. in 1st gear
Hole saws
25–68 mm dia. in 1nd gear
The numbers refer to the illustrations. The illustrations
can be found on the fold-out cover pages. Keep these
pages open while you read the operating instructions.
In these operating instructions, the power tool to which
these operating instructions apply is referred to as “the
tool”.
Description
The TE 2 / TE 2-E / TE 2-S / TE 2-M is an electrically pow-
ered rotary hammer with pneumatic hammering mech-
anism designed for professional use.
The following items are supplied: power tool, (quick-
release chuck TE 2-M), operating instructions, grease
(except TE 2-E), toolbox, side handle, cleaning cloth,
Depth gauge.
The following conditions must always be observed
when the tool is in use:
– The tool must be connected to an alternating current
electric supply in compliance with the information
given on the type plate.
– The tool is for hand-held use only.
– The tool must not be used in places where the sur-
rounding conditions may present a risk of explosion.
– Changes or modifications to the tool are not per-
missible.
– To avoid the risk of injury, use only the genuine Hilti
accessories and additional equipment specified for
use with this tool.
– Observe the information printed in the operating
instructions concerning operation, care and main-
tenance. The tool and its ancillary equipment may
present hazards when used incorrectly by untrained
personnel or when used not as directed.
– The tool is intended for professional use.The tool
may be operated, serviced and repaired only by
authorized, trained personnel. This personnel must
be informed of any special hazards that may be
encountered.
Main features of the tool
Class II electrical protection (double insulated)
Z
Mechanical torque-limiting clutch
Grip and side handle with vibration absorption
TE-C chuck
TE-C insert tool system
Variable speed switch
Rotary-only drilling mode
Gearing and hammering mechanism with permanent
grease lubrication
Pivotable side handle (360°)
Mechanical depth gauge
Interface for quick-release chuck (TE 2-M)
Precision hammering action (TE 2-S)
High spindle speed without hammering action (TE 2-M)
Lockbutton for sustained operation
Right of technical changes reserved
02_BA_TE2_S_M_P1_en.qxd:02_BA_TE2_S_M_P1_en.qxd 29.9.2012 9:53 Uhr Seite 12
Printed: 14.02.2014 | Doc-Nr: PUB / 5170540 / 000 / 00
