*2021356*
2021356
English
17
5
Operation
5.1
Removing the saw blade
WARNING
Risk of burning injury.
A hot accessory tool, clamping flange or clamping screw and the sharp edges of the
saw blade present hazards.
▶
Wear protective gloves when changing saw blades.
1. Disconnect the supply cord plug from the power outlet.
2. Press the arbor lockbutton.
3. Turn the saw blade clamping screw with the hex key until the arbor lockbutton engages fully.
4. Use the hex key to slacken the clamping screw by turning it counter-clockwise.
5. Remove the clamping screw from the outer clamping flange.
6. Open the pivoting guard by swinging it clear and remove the saw blade.
5.2
Fitting the saw blade
CAUTION
Risk of damage
Unsuitable or incorrectly fitted saw blades may damage the saw.
▶
Only use blades which are suitable for this saw. Observe the direction-of-rotation arrow on the saw
blade.
1. Disconnect the supply cord plug from the power outlet.
2. Clean the mounting flange and the clamping flange.
3. Fit the mounting flange.
4. Open the pivoting guard.
5. Fit the new saw blade.
6. Fit the outer clamping flange.
7. Secure the clamping flange with the clamping screw by turning it clockwise. At the same time, use one
hand to hold down the arbor lockbutton.
8. Before using the power tool, check that the saw blade is correctly seated and tightened securely.
5.3
Adjusting the cutting depth
1. Disconnect the supply cord plug from the power outlet.
2. Rest the circular saw on a flat surface.
3. Release the cutting depth adjustment clamping lever.
4. Lift the circular saw in a scissoring movement and set the cutting depth.
◁
The cutting depth is shown on the cutting depth scale.
For a clean-edged cut, set cutting depth to the thickness of the material plus 2 mm.
5. Secure the cutting depth adjustment clamping lever.
5.4
Setting the miter cut angle
1. Disconnect the supply cord plug from the power outlet.
2. Release the cutting angle adjustment clamping lever.
3. Pivot the base plate to the desired miter cut angle.
◁
The miter cutting angle is shown on the miter cut angle scale.
4. Tighten the cutting angle adjustment clamping lever.
5.5
Selecting a miter cut angle presetting
1. Disconnect the supply cord plug from the power outlet.
2. Release the cutting angle adjustment clamping lever.
3. Pivot the base plate to the 0° position.
Printed: 23.04.2018 | Doc-Nr: PUB / 5070536 / 000 / 06
Summary of Contents for SCW 70
