*2272031*
2272031
English
15
1. Clean the clamping flange and the quick-release clamping nut.
2. Check that the O-ring is in place in the clamping flange and that it is undamaged.
▶
Replace the O-ring if it is missing or damaged.
3. Fit the clamping flange on to the spindle (keyed fit to prevent slipping and rotation).
4. Fit the accessory tool.
5. Screw on the
Kwik lock
nut until it is seated against the accessory tool.
▶
The name
Kwik lock
should be visible when the nut is screwed on.
6. Press the spindle lock button and hold it in this position.
7. Firmly turn the accessory tool clockwise by hand until the
Kwik lock
nut is tightened securely and then
release the spindle lock button.
6.10.4 Removing an accessory tool secured with a Kwik lock nut
WARNING
Risk of breakage and irreparable damage.
If the spindle lockbutton is pressed while the spindle is
rotating, the accessory tool can detach from the power tool.
▶
Press the spindle lockbutton only when the spindle has stopped rotating.
1. Press the spindle lockbutton and hold it in this position.
2. Release the
Kwik lock
nut by turning it counterclockwise by hand.
3. If the
Kwik lock
nut cannot be released by turning it by hand, use a pin wrench to turn the nut in a
counterclockwise direction.
Never use a pipe wrench! A pipe wrench could damage the
Kwik lock
nut.
4. Release the spindle lockbutton and remove the accessory tool.
6.10.5 Installing core bit
1. Fit the side handle. → page 13
2. Fit the guard. → page 13
3. Place the core bit in position and tighten it hand-tight.
4. Press the spindle lock button and hold it in this position.
5. Tighten the core bit with a suitable open-end wrench.
6.10.6 Installing wire brush
1. Fit the side handle. → page 13
2. Fit the guard. → page 13
3. Place the wire brush in position and tighten it hand-tight.
4. Press and hold down the spindle lock button.
5. Tighten the wire brush with a suitable open-end wrench.
6.10.7 Fitting the abrasive resin-fiber wheel
1. Fit the side handle. → page 13
2. Fit the guard. → page 13
3. Fit the support plate and the abrasive resin-fiber wheel, screw on the clamping nut and tighten it securely.
4. Press and hold down the spindle lock button.
5. Use the pin wrench to tighten the clamping nut.
7
Operation
7.1
Grinding
CAUTION
Risk of injury.
The accessory tool may suddenly stick or stall.
▶
Use the product with the side handle (or optional hoop handle) fitted and always hold the product securely
with both hands.
Do not allow the accessory tool to jam and avoid excessive pressure on the product.
Summary of Contents for NURON AG 5D-22 125
