![background image](http://html1.mh-extra.com/html/hilti/dsh-fsc/dsh-fsc_assembly-instructions-manual_2135931008.webp)
2
en
DSH-FSC floor saw cart assembly instructions
1. Safety precautions
G
Use this floor saw cart only in conjunction with the Hilti DSH 700 or DSH 900 gas
saws.
G
Observe the instructions and safety precautions listed in the operating instruc-
tions for your Hilti gas saw.
2. Assembling the floor saw cart
2.1 Fitting the handle
Fit the handle
햲
to the frame
햳
and secure it with the screw knob
햴
.
2.2 Fitting the wheel axle to the frame
Push the wheel axle
햵
into the holes in the frame
햳
and secure it with the screw
knob
햶
.
2.3 Fitting the second wheel
Secure the second wheel
햷
on the wheel axle
햵
by fitting the washer
햸
and split
pin
햹
.
2.4 Fitting the front wheel
Fit the front wheel
햺
to the front wheel axle
햾
and secure it with the washer
햻
and split pin
햽
.
2.5 Fitting the spray guard
Use the two the screws
헀
to secure the spray guard
햿
to the frame
햳
.
10
5
11
9
8
7
6
4
3
2
G
Note:
The machine mount is set in such a way that the saw arm of the DSH 900-
40 gas saw does not come into contact with the floor when cutting to full depth.
When used with the DSH 900-35, DSH 700-35 and DSH 700-30, the machine
mount must be fitted in a lower position in order to reach full cutting depth.
3.1 Disassembling the machine mount
Remove both hex. nuts
헁
and screws
헂
from the machine mount
헃
.
3.2 Fitting the machine mount in the lower position
Insert the two screws
헂
in the upper openings in the machine mount
헃
and secure
the machine mount to the frame
햳
once again.
G
Note:
When fitting the machine mount, take care to ensure it is aligned centrally.
16
15
14
13
12
3. Adjusting the machine mount
4. Adjusting for straight running
G
Note:
The floor saw cart is designed so that the gas saw cuts in a straight line
when the mark on the machine mount is in the middle position. If it is found that
the gas saw pulls to one side while cutting, this can be compensated by adjust-
ing the position of the machine mount.
4.1 Adjusting the machine mount
for straight running
Release the upper hex. nut
헁
on the machine mount
헃
and pivot the rear of the
machine mount toward the side to which the saw tends to pull when cutting.
17
5. Fitting the gas saw
to
18
26
1. Bring the height adjustment lever
헄
into the upper position.
2. Release the screw knob
헆
on the grip clamp
헅
.
3. Place the gas saw in the forward section of the machine mount with its wheels
positioned as shown in the illustration and then pivot the grip of the saw
Z
into
the grip clamp
헅
.
4. Secure the gas saw by tightening the screw knob
헆
.
5. Fit the water container
U
after filling it.
6. Adjust the position of the handle to bring it into a comfortable working position.
7. Adjust the disc/blade guard.
01_MA_DSH_FSC_P1.qxd:01_BA_DSH_FSH_P1.qxd 7.5.2010 11:16 Uhr Seite 2
Printed: 07.04.2015 | Doc-Nr: PUB / 5224914 / 000 / 00
Summary of Contents for DSH FSC
