background image

14

English

2153083

*2153083*

5. Select one of the following alternatives.

If the following conditions are met, also take this action:

Conditions

: Cutting using manual saw advance

Make sure that the traction drive is disengaged.

With both hands on the two grips provided, push the floor saw trolley in the

cutting direction.

If the following conditions are met, also take this action:

Conditions

: Cutting using the traction drive

Engage the traction drive. → page 13

Use the remote control unit to regulate the direction and speed of advance.

Pay attention to the cutting line indicator and keep the floor saw trolley tracking

along the line.

Stop saw advance at the end of the cut.

Disengage the traction drive. → page 13

6. Lift the saw blade out of the cut in the floor.

7. Run the floor saw back to the starting point.

8. Make the subsequent cuts as described above. Increase the cutting depth by 3 to

5 cm for each subsequent cut. In doing so, the maximum cutting depth must be

observed.

9. After completing the work, switch the saw off and unplug the supply cord.

10.Close the water flow regulator valve and turn off the water supply.

6.3 Adjusting the cutting line indicator

If the floor saw trolley continually pulls either to the left or right when following the

marked cutting line with the cutting line indicator, forcing the operator to making

steering corrections, it may be necessary to adjust the cutting line indicator.

1. Pull the securing pin out of the hollow bolt.

2. Pull the pointer out.

3. Release the locknut and unscrew it slightly, if necessary, until the hollow bolt can be

screwed far enough into the sleeve.

4. Depending on the desired change of direction, either screw the hollow bolt further into

the sleeve or unscrew and retract it slightly. In doing so, make sure that hole in the

hollow bolt again faces forwards and upwards.

5. Insert the pointer in the hollow bolt and position the pointer so that the holes in the

pointer and in the hollow bolt are in alignment.

 Printed: 07.05.2019 | Doc-Nr: PUB / 5492449 / 000 / 00

Summary of Contents for DSF 1030-TS

























Reviews: