![background image](http://html.mh-extra.com/html/hilti/ag-125-19se/ag-125-19se_original-operating-instructions_2135558023.webp)
English
17
1.4 Product information
Hilti
products are designed for professional use and may be operated, serviced and maintained only by
trained, authorized personnel. This personnel must be informed of any particular hazards that may be
encountered. The product described and its ancillary equipment may present hazards when used incorrectly
by untrained personnel or when used not as directed.
The type designation and serial number are printed on the rating plate.
▶
Write down the serial number in the table below. Always quote this information when you contact a Hilti
representative or Hilti Service to enquire about the product.
Product information
Angle grinder
AG 125-19SE
Generation
04
Serial no.
2 Safety
2.1 General power tool safety warnings
WARNING
Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in
electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
Work area safety
▶
Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
▶
Do not operate power tools in explosive atmospheres, such as in the presence of flammable
liquids, gases or dust.
Power tools create sparks which may ignite the dust or fumes.
▶
Keep children and bystanders away while operating a power tool.
Distractions can cause you to lose
control.
Electrical safety
▶
Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce risk of
electric shock.
▶
Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and
refrigerators.
There is an increased risk of electric shock if your body is earthed or grounded.
▶
Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the
risk of electric shock.
▶
Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the
risk of electric shock.
▶
When operating a power tool outdoors, use an extension cord suitable for outdoor use.
Use of a
cord suitable for outdoor use reduces the risk of electric shock.
▶
If operating a power tool in a damp location is unavoidable, use a residual current device (RCD)
protected supply.
Use of an RCD reduces the risk of electric shock.
Personal safety
▶
Stay alert, watch what you are doing and use common sense when operating a power tool. Do
not use a power tool while you are tired or under the influence of drugs, alcohol or medication.
A
moment of inattention while operating power tools may result in serious personal injury.
▶
Use personal protective equipment. Always wear eye protection.
Protective equipment such as dust
mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce
personal injuries.
▶
Prevent unintentional starting. Ensure the switch is in the off‐position before connecting to power
source, picking up or carrying the tool.
Carrying power tools with your finger on the switch or
energising power tools that have the switch on invites accidents.
▶
Remove any adjusting key or wrench before turning the power tool on.
A wrench or a key left
attached to a rotating part of the power tool may result in personal injury.
▶
Do not overreach. Keep proper footing and balance at all times.
This enables better control of the
power tool in unexpected situations.
Printed: 05.09.2016 | Doc-Nr: PUB / 5300508 / 000 / 00
Summary of Contents for AG 125-19SE
