background image

Regulatory Information 

FCC Information 
Please take attention that changes or modification not 
expressly approved by the party responsible for 
compliance could void the user’s authority to operate the 
equipment. 
FCC compliance: This equipment has been tested and 
found to comply with the limits for a Class A digital 
device, pursuant to part 15 of the FCC Rules. These limits 
are designed to provide reasonable protection against 
harmful interference when the equipment is operated in 
a commercial environment. This equipment generates, 
uses, and can radiate radio frequency energy and, if not 
installed and used in accordance with the instruction 
manual, may cause harmful interference to radio 
communications. Operation of this equipment in a 
residential area is likely to cause harmful interference in 
which case the user will be required to correct the 
interference at his own expense. 
FCC Conditions 
This device complies with part 15 of the FCC Rules. 
Operation is subject to the following two conditions: 
1. This device may not cause harmful interference. 
2. This device must accept any interference received, 
including interference that may cause undesired 
operation. 
EU Conformity Statement 

This product and - if applicable - the 
supplied accessories too are marked with 
"CE" and comply therefore with the 
applicable harmonized European standards 

listed under the Low Voltage Directive 2014/35/EU, the 
EMC Directive 2014/30/EU. 

2012/19/EU (WEEE directive): Products 
marked with this symbol cannot be 
disposed of as unsorted municipal waste in 
the European Union. For proper recycling, 
return this product to your local supplier 

upon the purchase of equivalent new equipment, or 
dispose of it at designated collection points. For more 
information see: www.recyclethis.info. 

2006/66/EC (battery directive): This product 
contains a battery that cannot be disposed 
of as unsorted municipal waste in the 
European Union. See the product 
documentation for specific battery 
information. The battery is marked with this 

symbol, which may include lettering to indicate cadmium 
(Cd), lead (Pb), or mercury (Hg). For proper recycling, 
return the battery to your supplier or to a designated 
collection point. For more information, see: 
www.recyclethis.info. 

Industry Canada ICES-003 Compliance 

This device meets the CAN ICES-3 (A)/NMB-3(A) 
standards requirements. 

Warning 
This is a class A product. In a domestic environment this 
product may cause radio interference in which case the 
user may be required to take adequate measures. 

 

Summary of Contents for U7T Series















Reviews: