background image

iv 

 

Warnings

 

 

All the electronic operation should be strictly compliance with the electrical 

safety regulations, fire prevention regulations and other related regulations in 
your local region. 

 

Please use the power adapter, which is provided by normal company. The power 

consumption cannot be less than the required value. 

 

Do not connect several devices to one power adapter as adapter overload may 

cause over-heat or fire hazard. 

 

Please make sure that the power has been disconnected before you wire, install 

or dismantle the device. 

 

When the product is installed on wall or ceiling, the device shall be firmly fixed.   

 

If smoke, odors or noise rise from the device, turn off the power at once and 

unplug the power cable, and then please contact the service center. 

 

If the product does not work properly, please contact your dealer or the nearest 

service center. Never attempt to disassemble the device yourself. (We shall not 
assume any responsibility for problems caused by unauthorized repair or 
maintenance.) 

 

 

Cautions

 

 

Do not drop the device or subject it to physical shock, and do not expose it to 

high electromagnetism radiation. Avoid the equipment installation on 
vibrations surface or places subject to shock (ignorance can cause equipment 
damage). 

 

Do not place the device in extremely hot (refer to the specification of the device 

for the detailed operating temperature), cold, dusty or damp locations, and do 
not expose it to high electromagnetic radiation. The appropriate temperature 
is 

-20

 to 65

 

The device cover for indoor use shall be kept from rain and moisture. 

 

Exposing the equipment to direct sun light, low ventilation or heat source such 

as heater or radiator is forbidden (ignorance can cause fire danger). 

Summary of Contents for LTK1802 Series















Reviews: